Bedienungsanleitung Aritech RXW8 (Seite 5 von 20) (Englisch, Holländisch, Französisch, Italienisch)

702694

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

The following diagram shows the alarm, low battery, supervisory and

tamper-trouble run mode LED indications.

INSTALLING THE QUIK BRIDGE

Table 2: Tools and accessories needed

MOUNTING THE QUIK BRIDGE

You must be free of static electricity before handling circuit boards. Touch

a bare metal surface or wear a grounding strap to discharge yourself.

1. Remove the receiver cover by pressing down on the top centre of the

cover (see Figure E1).

2. Press down on the lower right corner of the base until the lower right

latch releases the circuit board (see Figure F).

3. Remove the circuit board by pulling it away from the top 2 latches and

set it aside.

4. Hold the base against the mounting surface and mark the 3 mounting

holes (see Figure F).

5. Remove the base and install the anchors provided, if studs are not

present.

6. Mount the base on the wall with the screws provided.

7. Replace the circuit board on the base by sliding the top of the circuit

board under the top 2 latches, then press on the bottom of the circuit

board until it snaps under the lower right latch.

SECURING THE COVER

To help prevent accidental tamper alarms caused by cover removal, install

the 2 self-tapping screws (included) on top of the cover (see Figure E2).

SETTING UP THE RF868 RECEIVER, RXW8OM QUIK BRIDGE

OUTPUT MODULE AND CSXLCD KEYPAD

To program the RF Quik Bridge

and Receiver, you need to connect a

CSX75 LCD keypad, a RXW8OM Quik Bridge

Output Module and a RF868

Receiver by wiring the data, common ground and positive lines for power

and programming together. This is in effect a miniature system, with the

Receiver treating the Quik Bridge

as a panel.

You also need to provide a 12 V power supply to the Quik Bridge

. Power

can be taken from the panel, but the data input to the panel should be

disconnected.

Connecting the RF868 Receiver and the CSX75 LCD Keypad

to the Quik Bridge

1. Open the RF868 Receiver and CSX75 LCD Keypad.

2. Wire the data, common ground and positive lines for power and

programming to the RF868 Quik Bridge

. The control panel provides

power to the Quik Bridge

. Do NOT wire the DATA line back to the

control panel as this might damage your control panel (see Figure G).

Table 3: Quik Bridge

Terminal Connections

Connector 4 can be used as a temporary connection for the keypad. The

keypad can be removed after finishing the programming.

Powering the Quik Bridge

To connect power to the receiver:

1. Turn off or remove power from the panel and disconnect the battery.

2. Wire receiver terminals (GND) and (+12 V) to a non-switched 12 V

supply output on the control panel. Make sure you observe the correct

polarity (see Figure H).

3. Turn on or apply power to the panel.

PROGRAMMING THE QUIK BRIDGE

SYSTEM

There are several steps to be taken when programming the Quik Bridge

These include:

• Enrolling the Transmitters on the RF868 Receiver

• Programming the Outputs on the Quik Bridge

• Programming the panel

Programming data

The RF868 Receiver and Quik Bridge

are both programmed using the

CSXLCD keypad. The system is divided into modules. The Quik Bridge

one module and the Receiver is another.

Each module has locations, where options are programmed.

Each of these locations has 1 or more segments. Each segment has be-

tween 1-8 bits of data.

Steps

1. To enter programming mode, press * followed by the programming

code. The default programming code is !"#$

2. Enter the number of the module followed by #.

• Press %# to program the Quik Bridge

module.

• Make sure that the dipswitch on the RF868 Receiver is set to 32. Press

&"# to program the RF868 Receiver module.

3. Enter the location number followed by the # key. The first segment of

the location is displayed on the LCD.

4. 2 types of data can be programmed:

• Numerical data Enter a valid number from 0-255. For locations with a

maximum of 15, the hexadecimal equivalent is displayed in parenthesis.

• Feature selection data Enter the feature number of the segment that

you are turning on or off. If a feature is not enabled, a hyphen is displayed.

5. Press the * key to enter the data and move to the next segment. Press

# to leave the location before the last segment.

6. When you have programmed the last segment of the location, press

the * key to exit the location.

7. Enter another location number followed by the # key if you wish to

program another location.

8. Leave programming mode by pressing the Exit key on the keypad.

mralA

2enoznomralanasierehtfiyalpsiD

rettimsnart

yrosivrepuS

7enozanoyrosivrepusasierehtfiyalpsiD

.rettimsnart

yrettabwoL

5enozanoyrettabwolasierehtfiyalpsiD

rettimsnart

elbuorT-repmaT

elbuortrorepmatasierehtfiyalpsiD

rettimsnart8enozanonoitidnoc

revieceRFR

tcennocsid

regnolonsireviecer868FRehtfiyalpsiD

eludomtuptuoehtotdetcennoc

egdirBkiuQ

slanimreT

lenaP revieceR dapyeK

1010detcennoCtoNataD0101

+V21lenaPSOP8.31

-DNGlenaPMOCdnuorG

dedulcnI dedulcnitoN

srohcnadnaswercsgnitnuoM

dradnatsllamsdnarevirdwercsspilihP

revirdwercs

hctiwsrepmatrofgnirpSeriwdednartsmm2.0

yllacipyt(ylppusrewopCDV21

)lenapybdeilppus

deilppusyllacipyt(srotsiserLOE

lenapehthtiw

Aritech RXW8 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info