Bedienungsanleitung Aritech RXW8 (Seite 6 von 20) (Englisch, Holländisch, Französisch, Italienisch)

702694

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Enrolling the Transmitters

8 wireless transmitters can be enrolled on the RF868 receiver for use with

the Quik Bridge

. You can either enrol the transmitters individually or use

the auto enrol feature to enrol several transmitters at the same time. In

each case you must activate the tamper on the transmitter as shown in

Table 4.

Table 4: Transmitter activations

rettimsnarT noitcA

wodniW/rooDrevocehtevomeR

htiwwodniW/rooD

tcatnoclanretxe

revocehtevomeR

RIPrevocehtevomeR

rotcetedekomSetalpkcabehtevomeR

sbofyeknottub4

snottubmrasiDdnamrAehtsserP

ylsuoenatlumis

It is a good idea to make a note of the transmitter assigned to each zone on

the receiver.

Enrolling transmitters

1. Make sure that the dipswitch on the RF868 Receiver is set to 32.

2. To enter programming mode, press *$ followed by !"#$.

3. Press &"# to program the RF Receiver module.

4. Press '!%# to go to location 910. This loads the factory defaults

for the RF868 Receiver. The keypad beeps 3 times indicating that

loading is in progress. This takes about 6 seconds.

5. Press !'(# to go to location 194. Check that Segment 1 is set to 0

so that the starting zone is 1. Press # to leave the location.

6. Press % #! * to enroll transmitter 1. Open the tamper on the transmitter

and the keypad should chime to indicate that the transmitter has been

accepted.

7. Repeat step 6 for the other devices by entering %# transmitter number

* and opening the tamper on the transmitter for each device.

Auto enrolling transmitters

1. Make sure that the dipswitch on the RF868 Receiver is set to 32.

2. To enter programming mode, press *$ followed by !"#$.

3. Press &"# to program the RF Receiver module.

4. Press '!%# to go to location 910. This loads the factory defaults for

the RF868 Receiver. The keypad beeps 3 times indicating that loading

is in progress. This takes about 6 seconds.

5. Press !'(# to go to location 194. Check that Segment 1 is set to

0 so that the starting zone is 1. Press # to leave the location.

6. Press !'&# to go to location 193. Check that segment 2 is on to

allow sequential programming. Press # to leave the location.

7. Press % #!* to enrol transmitter 1. Open the tamper on the transmitter

and the keypad should chime to indicate that the transmitter has been

accepted.

8. Open the tamper on each other transmitter to enrol the devices

sequentially.

Unenrolling transmitters

1. To enter programming mode, press *$ followed by !"#$.

2. Press &"# to program the RF Receiver module.

3. Enter the transmitter number followed by #. For example, for transmitter

4, enter (#.

4. In Location 1 Segment 1 switch bit 1 off to disable the transmitter.

5. Press * to save the setting and # to leave the menu.

RF Supervision windows for Belgium and Holland

1. Make sure that the dipswitch on the RF868 Receiver is set to 32.

2. To enter programming mode, press *$ followed by !"#$.

3. Press &"# to program the RF Receiver module.

4. Press !')# to go to location 195.

For Holland and Belgium,check the correct values in Table 5.

Table 5: Supervision windows for Belgium and Holland

1tnemgeS 2tnemgeS 3tnemgeS

dnalloH

gnol(021

noisivrepus

)wodniw

gnol(021

noisivrepus

)wodniw

trohs(02

noisivrepus

)wodniw

muigleB

erif(021

srettimsnart

noisivrepus

)wodniw

erif(042

srettimsnart

noisivrepus

)wodniw

trohs(51

noisivrepus

)wodniw

RSSI values

1. To enter programming mode, press *$ followed by !"#$.

2. Press &"# to program the RF Receiver module.

3. Enter !''# to select location 199.

4. Enter XX* where XX is the zone number (1 through 8).

5. Now walk test the device.

6. After the device has transmitted, you can record the reading from

location 200. Enter "%%# and the RSSI Reading is displayed.

7. Note the RSSI reading and repeat steps 3 to 7 for the other detectors.

Using the 4 button keyfobs

The functions of the Star and the Light buttons can be used to trigger

outputs. This can be achieved by programming receiver options 4 and 5

of the zone segment where the keyfob was enrolled.

Table 6: Supervision windows for Belgium and Holland

nottuBthgiL ffO4noitpO nO4noitpO

desUtoNlortnoC1tuptuO

nottuBratS ffO5noitpO nO5noitpO

desutoNlortnoc2tuptuO

Using the Light and Start button on keyfobs to trigger outputs.

1. To enter programming mode, press *$ followed by !"#$.

2. Press &"# to program the RF Receiver module.

3. Enter the transmitter number followed by #. For example, for transmitter

4 enter (#.

4. In segment 1 of this location, switch bit 4 and bit 5 On to enable the

Light and the Star button.

5. Press * to save the setting and # to leave the menu.

You must then program the corresponding event in table 8 so that

pressing the button on the keyfob activates the output.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Aritech RXW8 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info