Bedienungsanleitung Atika ADH 254 A (Seite 16 von 44) (Deutsch, Englisch, Holländisch, Französisch)

555721

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Electrical safety

 Extension cable to be designed in compliance with IEC 60

245 (H 07 RN-F) having a core cross-section of at least:

− 1.5 mm² for cable lengths up to 25 m

− 2.5 mm² for cable lengths over 25m

 Long and thin connection lines result in a potential drop. The

motor does not reach any longer its maximal power; the

function of the device is reduced.

 Plugs and coupler outlets on connection cables must be

made of rubber, non-rigid PVC or other thermoplastic

material of same mechanical stability or be covered with this

material.

 Protect yourself against an electric shock. Avoid touching

earthed parts with your body.

 The connector of the connection cable must be splash-proof.

 Wind off completely the cable when using a cable drum.

 Do not use the cable for purposes for which it is not meant.

Protect the cable against heat, oil and sharp edges. Do not

use the cable to pull the plug from the socket.

 Regularly check the cable and if damaged, have it renewed

by a recognised skilled electrician.

 When running the connection line observe that it does not

interfere, is not squeezed, bended and the plug connection

does not get wet.

 Regularly check the extension cables and replace them if

they are damaged.

 Do not use any defective connection cables.

 Do not set up any provisional electrical connections.

 Never bypass protective devices or deactivate them.

 Only hook up the machine by means of a fault-current circuit

breaker (30 mA).

The electrical connection or repairs to electrical parts of the

machine must be carried out by a certified electrician or

one of our customer service points. Local regulations –

especially regarding protective measures – must be

observed.

Repairs to other parts of the machine must be carried out

by the manufacturer or one of his customer service points.

Use only original spare parts and accessory parts.

Accidents can arise for the user through the use of other

spare parts. The manufacturer is not liable for any damage

or injury resulting from such action.

Before the first start-up



To achieve flawless functioning of the machine, please

follow the instructions listed:

 Place the surface planing and thicknessing machine at a

location which meets following conditions:

− secured against slipping

− free of vibrations

− even

− free of tripping hazards

− adequate light

 Before each use, check

− Connection cables for defects (cracks, cuts, etc.).

Do not use any defective cables.

− whether the pushstick is to hand

− Is the unused blade shaft covered by the blade shaft

guard?

 When working do not stand directly in front or behind the

machine but stand to the side.

You have to attach the following parts:

Base frame A1 - A7

 Assemble the four parts of the stand as shown in the figures

A1 through A7.

 Use a second person to place the surface planing and

thicknessing machine on the stand.

 Secure the surface planing and thicknessing machine to the

stand.

Securing on the floor A8

Secure the surface planing and thicknessing machine to the

floor using 4 screws.

Guide plate

 Secure the guide plate guideway (7) to the housing.

 Slide in the guide plate holder (10) and secure the locking

lever (12).

 Mount the guide plate (13).

Shavings exhauster C1 - C7

 Install the shavings exhauster connector (16).

 Connect the shavings exhauster hose (17) and secure it

using a hose band clip (18).

 Connect the shavings exhauster hood (27) to the exhaust

hose and tighten the hose band clip.

 Attach the shavings bag (19) to the exhauster connector and

secure it using the hose band clip.

Start-up

Mains connection

Compare the voltage listed on the machine’s type plate, e.g.

230 V, with the mains voltage and connect the machine to a

suited and properly earthed electrical socket.



Alternating current motor:

Use a shockproof plug, mains voltage 230 V with residual

current circuit breaker and min. 10 A inert fuses.



Three-phase motor:

CEE socket, 3-pin, mains voltage 400 V with earth-leakage

circuit breaker and min. 10 A fuse.

 Use connection cable or extension cable respectively with a

cross section of at least 1.5 mm².

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Atika ADH 254 A Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Atika ADH 254 A

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info