Bedienungsanleitung Atika ADH 254 A (Seite 18 von 44) (Deutsch, Englisch, Holländisch, Französisch)

555721

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Planing and joining workpieces

Adjusting the guide plate

1. Loos

the locking lever, pull out the

en the locking lever (12).

If you can not sufficiently turn

lever head and turn it back.

Tilt the guide plate to your desired angle which you can read

from the angle scale (40). M

ake sure that the lower edge of

the guide plate is above the table edge when tilting. E8

Tighten the locking lever (12) again.

Adjusting the depth of cut

1. Turn h of cut (29) the adjusting screw for the dept

2. You can read it from the depth of cut scale (45).

Adjusting the blade shaft guard

1. Pus .

ard (46)

inst the guide plate (13)

e table plate and

h the workpiece against the guide plate

2. Loosen the clamping device for the blade shaft gu

3. Turn the adjusting screw (30) to adjust the arm of the blad

shaft guard.

4. For flat workpieces (< 75 mm):

Push the blad

e shaft guard (23) aga

and lift it according to the w

orkpiece thickness. Turn

therefore the adjusting screw (30):

Push the workpiece somewhat below the blade shaft guard

and lower the latter onto the workpi

ece.

For high workpieces (> 75 mm):

Lower the blade shaft guard down to th

push it against the workpiece. E12

Planing

1. S ar .

ce right-angled over the feed table plate.

diately

t t the motor

2. Push the workpie

3. Hold your fingers close to each other and guide th

workpiece with flat hands over the feed table plate.

4. When planing narrow surfaces (joining edges) push the

workpiece with both hands and clenched fists ag

ainst the

guide plate and the table plate and push it over the feed

table plate.

When planing and joining short workpieces use the push

stick (31)

6. Press down the workpiece only on the delivery table.

7. Turn the machine off if the work is not imme

continued.

Skewing

1. Plac ece against the tilted guide plate.

cts the

cknessing is to make the workpiece with

ce thinner.

e already planed surface faces

t the workpiece

Prep

e the workpi

2. Adjust the blade shaft guard so that it just conta

workpiece.

3. With your left clenched fist press the workpiece against the

guide plate

and the delivery table plate. Push the workpiece

with your closed right hand over the feed table plate.

Turn the machine off if the work is not immediately

continued.

Thicknessing

The purpose of thi

already planed surfa

For this the workpiece is guided through the machine and

machined on its top surface. Th

the thicknessing table plate. The feed direction is exactly the

other way round as for planing from left to right.

 When thicknessing a step will be formed on the lead and

edges of the workpieces. Therefore cu

tail

to length only after thicknessing

arations:

Pull the mains plug before performing

settings.

Installing the dust extractor

Loos sh the blade shaft

grooves of the table plate.

1. en the locking lever (46) and pu

d off from the table plate.

2. Adjust the guide plate (13) to 90° and slide it beyond the

edge of the table plate.

3. Place the extractor hood (27) onto the planing plate. Slide

two fixing brackets in the

4. Make sure that the shavings exhauster hose and the bag

are secured.

Thicknessing

Mak icknessing adjusting lever (35) is in its

e machine can cut 2 mm as a

r do only adjust this depth if:

width of which is

3. Start

angled in arrow

e drawn in automatically.

mediately

1. e sure that the th

osition.

top

2. Adjust the depth of cut.

 In a single pass th

maximum. Howeve

− your blades are very sharp,

− you machine soft wood types,

− you machine workpieces the

smaller than the maximum width

the motor.

the workpiece slowly and right-

4. Push in

direction. It will b

5. Guide the workpiece straight through the machine.

Turn the machine off if the work is not im

continued.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Atika ADH 254 A Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Atika ADH 254 A

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info