Bedienungsanleitung Atika ADH 254 A (Seite 19 von 44) (Deutsch, Englisch, Holländisch, Französisch)

555721

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Maintenance and cleaning

Before each mainte

− switch off device

nance and cleaning work

Maintenance an is

is only a y service staff.

the following to maintain the operability of the

R lints and dust only with a brush or vacuum

ustment device of the thicknessing table.

ial



this purpose put the clamping



h a mild

s are wearing parts and will become dull after

t use.

− wait until the machine comes to a stop.

− pull out power plu

d re hose described in thpair work other than t

llowed to be carried out b

chapter

For maintaining and cleaning, removed security devices must

unconditionally be mounted properly and proved again.

Use only original parts. Other parts can result in unexpected

damages and injuries.

Cleaning

 Observe

machine

 Do not wash down device with water.

emove sp



cleaner.

 Slightly spray maintenance spray or dry-film lubricant on the

height adj

 Take care that the feed rollers remain free of rust and

resin.

 Remove resin residues from the table plate surfaces.

 Resin residues can be removed with a commerc

main nance and care spray.

Apply a thin film of sliding wax on the feed, delivery and

thicknessing table plates.

 Regularly remove resin from the blade shaft and from the

parts attached to it. For

device, the blade holders and the blades into paraffin,

gasoline or commercial resin remover for 24 hours.

Carefully shake out the shavings bag. Manually wash it in

case of heavy soiling but at least once a year wit

soap solution.

intenance M

The cutting blade

longer or frequen

 If so, replace the cutting blades or have them sharpened.

Regrinding of cutting blades is only allowed to a height o

15 mm.

Alwa

ee “T data”).

ys use cutting blades which are approved for the machine

echnical

Replace or sharpen both cutting blades together.

Before replacing or sharpening

blades unplug the machine.

the cutting

Danger

cuttin b

of cutting! Wear gloves when replacing the

lades.

Replacing the cutting blades

1. Adju slide it beyond the

late.

st the guide plate (13) to 90° and

of the table plate.

2. Loosen the locking lever (46) and push the blade shaft

guard off from the table p

3. Screw in the clamping screws (34) using the delivered open-

end spanner (32). G1 - G2

If the nuts are not visible, carefully turn the blade shaft (47)

using a waste wood block.

5. blade slots in the blade shaft.

e cutting blades onto

ble plate.

of the setting gauge is flush

Remove the blade (33). G3

Clean all parts including the

6. Reinstall a new or sharpened blade.

7. Align the blade:

− Place the setting gauge (53) for th

the delivery ta

− Firmly press the gauge onto the delivery table plate while

making sure that the edge

with the edge of the delivery table plate. G4

Then, the setting gauge presses the blade in its correct

position.

−

− ng so start in the centre and move outwards.

8. lade shaft.

− Retighten the clamping screws.

When doi

Replace also the other blade of the b

Push the blade shaft guard over the blade shaft.

Maintenance of the gearbox

Perform every 50 operating

hours:

ove wood dust and shavings using a vacuum or a

e bearings of the belt roller and pulley.

the following steps approx.

1. Remove the gearbox cover (48).

2. Rem

brush.

3. Slightly spray maintenance spray on the roller chain (44)

and on th

Do not use grease.

ox cover.

Re-mount the gearb

Transport

Remove mains plug before each transport.



Before any

fully covers the blade shaft.

ft the machine.

transport make sure that the blade shaft guard

This will avoid injury by the blades.

Two persons are required to li

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Atika ADH 254 A Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Atika ADH 254 A

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info