Bedienungsanleitung Atika ADH 254 A (Seite 17 von 44) (Deutsch, Englisch, Holländisch, Französisch)

555721

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

On/Off switch D1

Do not use any device where the switch can not be

switched on and off. Damaged switches must be repaired or

replaced immediately by the customer service.

Switching on

Press the green button ( I ) on the switch.

If there is a power cut, the machine switches off

automatically. Push the green ( I ) button to start the

machine again.

Switching off

Press the red button. ( 0 )

EMERGENCY-STOP button



In an emergency case, the surface planing and

thicknessing machine can be cut off by pressing the

EMERGENCY-STOP button (21).

Motor protection (230 V only)



The motor is equipped with a safety switch and switches

off automatically when overloaded.

It can be switched back on following a cooling off phase

(5 – 10 min).

Press the

1. red button ( 0 ).

2. the small button next to the button (20)

3. the green button ( I ) to start

 Machine with 4

Ensure that

00 V 3~

the rotating

otating direction

ou can change the direction by

ust / chip exhaustion

direction of the blade shaft

matches the rotating

direction indicated on the

machine.

placing a screw-driver in the slot

provided in the plug collar, and

adjust the correct direction by

moving to the left or right applying

slight pressure.

The wood dust generated during operation impedes the

Ther e

necessary view and is harmful to health to some degree.

efore, always connect the shavings bag (19) to th

asis.

hood (27) is

shavings exhauster connector (16). C6 - C7

Empty the shavings bag on a regular b

 The motor will only start if the extractor

properly attached and thus releases the safety switch.

Working with the surface planing and

thicknessing machine

Before starting to work consider the following safety

 W

ing and thicknessing machine securely

he blade shaft?

have

advices to keep the risk of injuries as small as

possible.

orkplace tidied?

 Is the surface plan

installed?

 Are all fastening screws tightened?

 Are the blades securely fastened on t

 whether the pushstick is to hand

e machine until you

 You may not start to operate th

read these operating instructions, observed all the

instructions given and installed the machine as described!

Also, note the following important points:

 de shaft is

ers closed.

free



Make sure that the non-used area of the bla

covered by the blade shaft guard.

 Place yourself outside of the area of danger.

 Place your hands flat on the workpiece with fing

 Never remove loose splinters, chips, or similar by hand.

 Connect the shavings bag.

ollers and cutting tools are

 Make sure that the feed r

from wood shavings and dust.

 Do only machine workpieces the dimensions of which are

within the specifications for this machine (see “Technical

data”).

Do not guide back the workpiece over the open-running

blade shaft.

 Adjust the smallest cutting depth after your work is finished.

Observe all safety instructions in any case.

e planing is to smooth a rough surface

Surface planing

The objective of surfac

(planing), e.g. to smooth the edge of a board.

For this the workpiece is placed onto the feed table plate and is

machined on its underside. Feed direction is from right to left.

Preparations:

Pull the mains plug before performing

settings.

Installing the dust extractor

1. os crank handle (25) and Lo en the locking wheel (24) on the

turn the latter anticlockwisely to move the thicknessing table

plate to its lowest position. E2 - E3

Slide the shavings exhauster hood (27

2. ) under the feed table

plate. Slide two fixing brackets in the grooves of the table

plate. E4 - E5

Make sure that

3. the shavings exhauster hose and the bag

are secured.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Atika ADH 254 A Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Atika ADH 254 A

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info