Bedienungsanleitung Atmos A45SPT (Seite 45 von 72) (Englisch)

810414

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

Operation and Maintenance Manual - EN

www.atmos.cz EN-45

WARNING – after placing the exhaust sensor TSV on a side of the burner flue pipe, the

TSV temperature is not the exact temperature of the exhausts but the specific (differential)

temperature for the automatic start function. If you want to measure actual flue gas

temperature, install a flue gas thermometer in a flue gas duct between the boiler and chimney.

• Parameter S37 – characterizes the requires temperature of the boiler TK during which the pump in

the boiler circuit will be activated. This will only occur if the required temperature is reached and

the boiler is in OPERATION or burn-out mode (S14 = 13 with modules AD03 or AD08)… (75 °C)

It is also necessary to re-check or set parameters S38, S39, S40

• Parameter S38 – deactivation difference for parameter S37, of the pump in the boiler circuit

(S14 = 13 or S6 = 13)… (2 K)

If the temperature of the boiler TK drops by more than the deactivation difference S38, the pump

in the boiler circuit will be turned off in the OPERATION or STOP (burn-out) modes.

• Parameter S39 – characterizes the emergency temperature of the boiler TK, during which the

pump in the boiler circuit will be activated (S14 = 13 with modules AD03 or AD08)… (93 °C)

Activation will be carried out regardless of special functions of the burner (function S40). The

function works based on the deactivation difference specified in parameter S38.

• Parameter S40 – is the function for after-running of the pump in the boiler circuit used based on

boiler type (S14 = 13, S6 = 13)… (1)

a) S40 = 0…. The automatic deactivation function for the pump in the the boiler circuit after the

pellet burner burns out is off (after the time specified in parameter T5 runs out). The pump will

be switched off after the temperature of the boiler TK drops (S38, S39). Designated for ceramic

boilers with a large momentum (with the option of stoking with wood).

b) S40 = 1... The automatic deactivation function for the pump in the boiler circuit after the pellet

burner burns out is on. The pump will be switched off immediately after the burner burns out, after

the time specified in parameter T5 runs out. The function designated by parameter S39 is active.

Designated for boilers with minimal momentum without ceramics

(D30P, D31P, D40P, D50P,

DCxxSP(X)(T) and DCxxGSP)

• Parameter S41 – is the function for automatic burner cleaning with compressed air after a specific

number of working cycles (burn-out). The function assumes use of both reserve outputs (S6 = 16,

S14 = 15 (S67 = 15, S68 = 16 in case of AC07X-C module)) – non-standard function (4)

a) S41 = 1 - 9… function when the cleaning of the burner will be performed only once after ru-

nning a given number of cycles (1, 2, 3, 4, 5, 6, 7, 8, 9 - number of cycles)

b) S41 = 11 - 19… function when the cleaning of the burner will be performed always twice after

running a given number of cycles (11 = 1, 12 = 2, 13 = 3, 14 = 4, 15 = 5, 16 = 6, 17 = 7, 18 = 8,

19 = 9 - number of cycles) (from 1.4.2013)

If the parameter S41 = 0 or 10, the function is turned off.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Atmos A45SPT Seite 45

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info