Bedienungsanleitung Atmos A45SPT (Seite 46 von 72) (Englisch)

810414

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

www.atmos.cz

46-EN

Operation and Maintenance Manual - EN

• Parameter S42 – is the function for automatic burner cleaning with compressed air after a specific

period of operation time has passed (in one cycle). Once the subsequent working cycle has ended

(burn-out), the burner tubing is cleaned. The function assumes use of both reserve outputs (S6 = 16,

S14 = 15 (S67 = 15, S68 = 16 in case of AC07X-C module)) – non-standard function… (6 hours)

The value set is the actual time in hours.

• Parameter S43 – is the function for automatic burner cleaning with compressed air after a specific

period of operation time has passed. Once the set time has bassed, the burner immediately burns

out (AUTOSTOP), it is cleaned and once again run. If required at all requirements for START are

met. (regardless of S41 and S42 parameters). The function assumes use of both reserve outputs

(S6 = 16, S14 = 15 (S67 = 15, S68 = 16 in case of AC07X-C module)) – non-standard function…

(12 hours)

This is the sum of operating hours of all completed cycles.

The value set is the actual time in hours.

• Parameter S44 – is the compressor function for automatic cleaning of the burner by compressed

air, which determines the duration of compressor operation used for preparing a sufficient amount

of compressed air (pressure function S6 = 16) - nonstandard function… (2 min )

The set value represents the actual time in minutes.

• Parameter S45 – is the electric valve function for automatic cleaning of the burner by compressed

air, which determines how long the el. valve is open to perfectly clean the combustion chamber of

the burner (S14 = 15) - nonstandard function… (2 s)

The set value represents the actual time in seconds.

• Parameter S46 – is the burner fan function which sets the type of used fan with rotation scanning.

Number of impulses.… (

12-EBM

)

• Parameter S47 – is the function of fan 2 which sets the type of used fan with rotation scanning.

Number of impulses – do not change the factory setting… (0)

a) S47 = 12 - EBM..... radial blower of the burner

b) S47 = 4 - ATAS..... exhaust blower of the boiler

c) S47 = 0..... second method for switching off the blower 2 speed sensing

• Parameter S48 – characterizes temperature TEMPERATURE A in the applications of function

S6 = 17 to 36… (75 °C)

This is a free function for the reserve output R (R5) on the first position (Temperature A = first

position in function S6 = 17 to 36 (S67 = 17 to 36)).

• Parameter S49 – characterizes the activation or deactivation difference for TEMPERATURE A

in the applications of function S6 = 17 to 36… (5 K)

This is the difference for the free function of reserve output R (R5) on the first position (difference

for Temperature A = difference for the first position in the function S6 = 17 to 36 (S67 = 17 to 36)).

• Parameter S50 – characterizes TEMPERATURE B in the applications of function S6 = 25 to

36…(75 °C)

This is a free function for the reserve output R (R5) on the first position (Temperature b = second

position in function S6 = 25 to 36 (S67 = 17 to 36)).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Atmos A45SPT Seite 46

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info