Bedienungsanleitung Atmos A45SPT (Seite 48 von 72) (Englisch)

810414

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

www.atmos.cz

48-EN

Operation and Maintenance Manual - EN

• Parameter S60 – characterizes the amount of compressed air for the third pre-cleaning of the

burner when installing pneumatic burner cleaning. This is the time at which the partial filling

compressor air tank for pre-cleaning of the burner... (OFF) - standardly do not change

Adjustable range... OFF, 1 - 120 s.

• Parameter S61 – characterizes the function for control of the boiler exhaust fan from the outlet for

the burner discharge fan via the AD04 module. The function is intended for models DCxxSP(X),

CxxSP, ACxxSP without flap with actuator fitted with the pneumatic burner cleaning options and the

activated function for automatic start of the burner following wood burnout - AUTOSTART... (0)

a) S61 = 0....... function OFF

b) S61 = 1....... function ON (for for profile A45 pneu)

Never activate this function for boilers DCxxGSP and DCxxSP(X)(T), CxxSP, ACxxSP (Model

2018 equipped with flap with actuator).

• Parameter S62 – characterizes the function for control of the air valve (flap) with actuator (servo

drive) located in the pellet burner. This valve is operated from the outlet of the burner discharge fan

via the AD04 module built into the burner (from production) and then via the AD08 module from

the default configuration under the DCxxGSP hood. The function is intended for models DC40GSP,

DC40SPT (Model 2018)... (1)

a) S62 = 0....... funkce OFF (for burners without flap with actuator)

b) S62 = 1....... function ON (for burners with flap with actuator - for models DCxxGSP and

DCxxSP(X)(T), CxxSP, ACxxSP (Model 2018))

(Burners equipped with internal flap with actuator with AD04 module and the third (additional)

2-pins connector.)

• Parameter S63 – characterizes the function of start delay of the pellet burner (AUTOSTART),

with function of automatic burner start after burnout of the wood. Start delay of the pellet burner

we use in case, that the operator wants to switch the selector switch from the position - wood

to the position - pellets immediately after firing up without waitng till the boiler ran at nominal

output (TSV and TK temperatures not reached). This will always delay the start of the burner

60/120/180/240 minutes. When activating this function the display of the burner shows the time

remaining until the automatic start of the pellet burner (cold condition) or until the change to the

normal function of automatic start characterized with the parameter S34.

In case of that the operation waste gas temperature will be reached (parameter S36 = TSV + 20 K) ends

the countdown of the automatic start and the burner goes directly to normal auto start (parameter S34).

a) S63 = OFF... function switched off - factory stetting

b) S63 = 1... start delay of 1 hour (60 min) - recommended setting

c) S63 = 2... start delay of 2 hour (120 min)

(Setting possibility S63 = OFF, 1 (60 min), 2 (120 min), 3 (180 min), 4 (240 min))

This special function is active in the program version 38 and newer.

INFO - when putting burner into operation with activated function S63 = 1 (or 2, 3, 4) the

plumber may once enter the code 1111 and to skip from AUTOSTART directly to the burner

START (TSV and TK below than defined).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Atmos A45SPT Seite 48

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info