Bedienungsanleitung Audiovox AX-45 (Seite 6 von 8) (Englisch)

583752

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

128-6992

6 of 8

"Programming System Features" shown later in this installation guide to learn the operation of the valet/program/manual

override switch.

POWER DOOR LOCK HARNESS

3PIN White Plug w/3 Wires; Green, Blue & Blue/Red

The connection of the power door lock/unlock wires has already been explained. Route the three pin connector to the unit

and plug the connector into the mating white three pin connector shell of the control module. Do not force the connector,

it will only plug in one way.

PROGRAMMING FEATURES:

There are seven (7) Programmable Features on this system. Study the list below, keeping in mind the features and their

defaults, (how it comes programmed from the factory), and decide how best to program the UNIT for your particular

installation.

Programmable Features:

Features 1 Chirp 2 Chirp 3 Chirps Default

First Passive Arming Active Arming Active Arming

Second Ignition D/L ON Ignition D/L OFF Ignition D/L OFF

Third Ignition D/UL ON Ignition D/UL OFF Ignition D/UL OFF

Fourth Chirps ON Chirps OFF Chirps ON

Fifth Passive D/L Active D/L Active D/L

Sixth Siren Output Horn Output Horn Output

Seventh 800ms D/L Pulse 3.5 Sec. D/L Pulse 800ms D/L Pulse 800ms Door Lock

Double 800ms D/UL Pulses

To Program These Features:

Entering the Programming Mode involves operating the Ignition Switch and the Valet/Program/Manual Override Switch in

a particular sequence. This sequence is very time dependent, in other words it must be performed

quickly in order for you

to enter the mode. This sequence is also only one step different from the Transmitter Programming Mode, so make

certain you perform the sequence properly.

Upon entering the Programming Mode, the system is immediately set to allow adjustment of the First Programmable

Feature. That First feature, "Passive or Active Arming", can then be set ON or OFF by pressing the lock button of the

transmitter. The system confirms that it is set to adjust the First feature by repeatedly flashing the LED once, with a pause

in between each flash. The system will then report how the feature has been set by the number of chirps heard after

pressing the transmitter button. Toggling the Valet/Program/Manual Override Switch once again will advance you to the

Second Programmable Feature, confirmed by a repeating two LED flashes, with a pause in between each flash, etc.

It is important to note that when you first enter the Programming Mode, you are automatically positioned to adjust the First

Programmable Feature and that the Valet/Program/Manual Override Switch allows you to toggle from there through each

of the six more programmable features. However, it will not allow you to return to any feature once you have toggled past

it. Should you accidentally toggle past the feature you wanted to program, you must exit and re-enter the Programming

Mode and then adjust the feature you missed.

It is also important to note that you may toggle past as many programmable features as you wish without having to adjust

them. Each time you toggle forward to a new feature, the horn will chirp the appropriate number of times (1, 2, or 3 times)

to indicate how that feature is currently set, and the LED will flash the appropriate number of times to indicate the number

of the feature (First through Seventh) that you are set to adjust. For example, you might enter the mode and toggle the

Valet/Program/Manual Override Switch 3 times in order to adjust the Fourth programmable feature. The system would

respond with 1 Chirp, and the LED would begin to flash 4 Flashes, pause, and repeat. This has told you that the system

is ready for you to adjust the Fourth programmable feature, and that it is currently programmed for Chirps ON. A single

press of the lock button of the transmitter will cause the system to produce 2 Chirps. This signifies that you have

changed the programming to Chirps OFF. Please follow the programming procedure on the next page, and refer to the

list of the Programmable Features above when programming the system.

To program these selectable features;

Action System Response LED Response

Turn ignition on No response

Turn the valet switch on then off 3 times 1 Chirp - LED 1 flash

Within 3 seconds, turn ignition Off Short chirp, then long chirp

First Then On 2 chirps = active arming 1 Flash pause

Press transmitter Lock button to change 1 chirp = passive arming

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Audiovox AX-45 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info