Bedienungsanleitung Bell phones Big Button Plus 20270 (Seite 12 von 18) (Englisch)

648619

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

11 010508A-1

is a long distance call and the

service is provided by your local

phone company.

END OF LIST

• Indicates that the end of the call

history list is reached while using

the review UP and DOWN buttons.

REAL TIME CLOCK DISPLAY

• If the unit is in standby mode, the

display will show the current real

time clock, date, count for total

number of calls and new calls

received.

CALL TIMER

•

If the unit is in OFF-HOOK state,

the display will show the IN

USE icon “

” and start to count

the talking time about 5 seconds

later. The conversation time counts

up to 59 minutes and 59 seconds

when activated. The call timer stays

on approximately 3 seconds after

the conversation by pressing the

Hook Switch or returning the

handset to the base cradle.

LOW BATTERY WARNING

•

The LCD panel will display the

Low Battery icon “ ” on the

first line of the LCD panel to

indicate that the AAA batteries are

below operating voltage.

•

It is recommended to review all call

records before removing batteries.

REPEAT CALL INDICATION

• If an incoming call message has

been recorded previously, the LCD

panel will show “REPEAT”.

Only the most recent call record is

recorded in memory.

MESSAGE WAITING OR MSG

•

If you have Message Waiting

messages stored in the mailbox

(provided by your local phone

company). Upon receiving the

Message Waiting message, the

“MSG WAITING” will be

displayed on the LCD panel for a

short time and the NEW CALL

LED Indicator will start to blink.

And “MSG” icon will display flash

on top of the LCD screen. Once you

have retrieved the messages, the

“MSG” icon will disappear from the

panel and the NEW CALL LED

indicator will turn off after all new

call messages have been reviewed.

Message Waiting Indication is not

yet supported in all areas.

LINE ERROR

On rare occasions, the Caller ID

information sent by the telephone

company may have an error in the

transmission. This is not the fault of

your Caller ID unit. It can only

capture and store the data that was

received.

•

If a line error is detected in the

transmission, the LCD panel will

display “LINE ERROR ”.

TELEPHONE OPERATION

Dialing Mode (PULSE/TONE Switch)

•

If your home is equipped with

touch-tone dialing service, set the

PULSE/TONE switch to TONE

position.

• If you have a pulse (rotary) dialing

service, set the PULSE/TONE

switch to PULSE position.

Pulse>Tone (Mixed Mode) Dialing

If you only have pulse (rotary dialing)

service in your area and want to access

tone dialing services, set the

TONE/PULSE switch to the PULSE

position. Dial the desired number and

when tone signals are required press the

TONE button once. Subsequent digits

will be dialed in tone mode. Dialing

will be reset to Pulse mode when

handset is returned on-hook.

Adjusting Speaker Volume

You can adjust the speaker volume

during conversation with the caller or

LOW

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bell phones Big Button Plus 20270 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info