Bedienungsanleitung Benning Duspol Expert (Seite 8 von 63) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

577300

Zoom out

Zoom in

Vorherige Seite

1/63

Nächste Seite

01/2014

DUSPOL

expert



phase) on. Protective clothing and insulating conditions on site

might impair the function.

8. Continuity test(gureH)

- Thecontinuity test must becarried out on systemparts

whicharefreeofvoltage.Ifnecessary,capacitorshaveto

be discharged.

- ApplythetwoprobetipsL1/-

and L2/+

tothesystem

parts to be tested.

- Incaseofcontinuity(R<100kΩ),anacousticsignalis

emittedandtheyellowLEDΩ

forcontinuitylightsup.

This function also can be used to determine the conducting

and non-conducting direction of semiconductor components.

- If a voltage is applied to the test point, the voltage tester

automatically switches over to the voltage test function

and indicates this function.

9. Cable break detector (gureI)

- The cable break detector is intended for the non-contact

localization of cable breaks on exposed live lines.

FullygraspthedisplayhandleL2

and pass the detector

over a live line (e.g. a cable reel or a chain of lights) from the

feeding point (phase) in direction of the other end of the line.

- Aslongasthelineisnotinterrupted,theyellowLEDΩ

forcontinuityisflashing.

- The point of the cable break has been localized as soon as

theyellowLEDΩ

goes out.

Note:

The cable break detector can be used in earthed mains from

230V,50Hz/60Hz(phasetoearth)on.Protectiveclothing

and insulating conditions on site might impair the function.

10. Measuring point illumination(gureJ)

- The measuring point illumination

can be switched on

withtheprobetipsbeingopenbyactuatingthepush-but-

ton

ofthedisplayhandleL2

(1 second).

- Theoffautomaticallyafter10seconds.

11. Battery replacement(gureK)

- Donotapplyvoltagetothedevicewhenthebatterycom-

partment is open!

- Thebatterycompartmentislocatedonthebackofthedis-

playhandleL2

- Unscrew the screw of the battery compartment cover

andreplacetheusedbatteriesbytwonewmicrobatter-

ies (LR03/ AAA). Make sure that the new batteries are

insertedwithcorrectpolarity!

- Placethebatterycompartmentcoverontothedisplayhan-

dle L2

and tighten the screw.

12. Technical data

- regulation:DINEN61243-3:2011,IEC61243-3:2009

- nominalvoltagerange:12Vto1,000VAC/DC

- nominalfrequencyrangef:0to500Hz

- max. indication error: U

±15%,ELVU

+0%-15%

- internalresistanceofmeasuringcircuit:175kΩ,

- current consumption of measuring circuit: I

< 6,0 mA

(1.000V)

- current consumption of load circuit: I

<550mA(1,000V)

- polarityindication:+24VLED,-24VLED,+12VLED,-

12VLED(withpush-buttonsbeingactuated)

- polarityindication:+12VLED,-12VLED

- external conductor (phase indication) test and phase se-

quencetest:≥U

230V,50/60Hz

- continuitytest:0to100kΩ,LED+buzzer,testingcurrent:

 max.10μA

- cablebreakdetector:≥U

200V

- vibrationmotor,start:≥U

230V

- overvoltagecategory:CATIV600V,

CATIII1,000V

protectioncategory:IP65(DINVDE0470-1IEC/EN60529)

6 - first index: protection against access to dangerous

parts and protection against solid impurities, dustproof

5 - second index: protected against water jets. The device

can also be used in the rain.

- max.allowableDutycycle:30s(max.30seconds),240s

off

- battery:2xmicro,LR03/AAA(3V)

- weight: approx. 250g

- length of connecting cable: approx. 1,000 mm

- operating temperature and storage temperature range:

-15°Cto+55°C(climaticcategoryN)

- times of controlled reduction (thermal protection):

 voltage/time:230V/30s,400V/9s,690V/5s,1000V/2s

- responsetimeofthedisplay:750ms

13. General maintenance

Cleantheexteriorofthedevicewithacleandrycloth.

Ifthereiscontaminationordepositsintheareaofthebattery

orthebattery housing, clean theseareasas well by means

ofadrycloth.

If the device is stored for a longer period of time, remove the

batteries from the device!

14. Environmental protection

Please lead batteries and also the device at the end

of its useful life to the available return and collection

systems

Benning Duspol Expert Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info