Bedienungsanleitung Benning MM 4 (Seite 20 von 120) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch, Türkisch, Schwedisch)

577333

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

09/ 2013

BENNING MM 4



- Plug the black safety test lead into the COM socket 7 (black).

- Plug the red test probe into the V-Ω socket 8 (red).

- With the slide switch 2, the function button 4 and the RANGE button 6 of

the BENNING MM 4, select the desired range.

- Contact the measurement points with the black safety test lead and the red

test probe. The measured value appears in the digital display 3.

Note:

In low voltage ranges, the zero volts display does not appear due to interference

when the safety test leads are open. Check that the BENNING MM 4 is fully

functional by short-circuiting the test probe.

See fig. 2: DC-voltage measurement

See fig. 3: AC-voltage measurement

8.3 Resistance measurement

- With the slide switch 2, the function button 4 and the RANGE button 6 of

the BENNING MM 4, select the desired range.

- Plug the black safety test lead into the COM socket 7 (black).

- Plug the red test probe into the V-Ω socket 8 (red).

- Contact the measurement points with the black safety test lead and the red

test probe. The measured value appears in the digital display 3.

Important:

To obtain accurate measurements, ensure that no voltage is applied to the

measuring point.

With smaller resistances, the result can be improved by measuring the resist-

ance of the safety test lead beforehand by short-circuiting the test probe and

subtracting this resistance figure from the result.

See fig. 4: Resistance measurement

8.4 Continuity test with buzzer

- With the slide switch 2 and the function button 4 select the range marked

with the buzzer symbol „ “ on the BENNING MM 4.

- Plug the black safety test lead into the COM socket 7 (black).

- Plug the red test probe into the V-Ω socket 8 (red).

- Contact the measurement points with the black safety test lead and the red

test probe. When the resistance between the measuring points drops below

50 Ω, the buzzer integrated in the BENNING MM 4 sounds.

See fig. 5: Continuity test with buzzer

8.5 Diode testing

- With the slide switch 2 and the function button 4 select the range marked

with the diode symbol „ “ on the BENNING MM 4.

- Plug the black safety test lead into the COM socket 7 (black).

- Plug the red test probe into the V-Ω socket 8 (red).

- Contact the diode connections with the black safety test lead and the red test

probe. The value measured appears in the digital display 3.

- For Si diodes located in conducting direction, the flow voltage of 0.500 V to

0.900 V is indicated. The reading “000” indicates a short circuit in the diode,

and the reading “OL” an interruption in the diode.

- For a diode located in the non-conducting direction “OL” appears. If the

diode is defective, “000” or other figures appear.

See fig. 6: Diode testing

8.6 AC current measurement with the current transducer



Do not apply voltage to the output contacts of the current

transducer. The current transducer should be applied to a live

conductor only when it is connected with the Multimeter.

Max. current of enclosed current transducer 300 A!

8.6.2 Current measurement

- Contact the current transducer firmly with the Multimeter.

- Switch on the voltage measurement on the Multimeter. Press the blue but-

ton 2 s and select the desired range with the RANGE button. (Amp CLAMP)

- Press the opening lever 9. With the current transducer, grip the single-wire

conductor with the current to be measured.

- The reading appears in the digital display 3.

See fig. 7: AC current measurement with current transducer

9. Maintenance



Before opening the BENNING MM 4, always ensure that it is not

connected to a source of voltage! Electrical hazard!

Any work required on the BENNING MM 4 when it is under voltage must be

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Benning MM 4 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info