680440

Berner C500 Seite 30

30
Zoom out
Zoom in
Vorherige Seite
1/144
Nächste Seite
NOTE:
• Contrary to the illustrated section, use the appropriate
connectors (e.g. for timber gates use woodscrews), as
well as the proper hole depths for other gate types.
• Contrary to the illustrated section, the required core hole
diameter may vary depending on material thickness or
strength. The required diameter may be Ø 5.0–5.5 mm
for aluminium and Ø 5.7 – 5.8 mm for steel.
Fitting:
▶
See Figures4–4.3
The sliding gate operator must be released (see Figure3.2).
▶
When fitting the toothed tracks, make sure that the
transitions between the individual toothed tracks are
properly aligned to ensure smooth gate movement.
▶
After fitting, the toothed tracks and the toothed wheel of
the operator must be aligned to each other. Both the
toothed tracks and the operator housing can be adjusted
to do this.
Incorrectly fitted or poorly aligned toothed tracks may
lead to unintentional reversing. It is essential that the
specified dimensions are adhered to!
▶
Seal the housing to protect it from humidity and vermin
(see Figure 4.4).
3.4 Sliding gate operator electrical connection
▶
See Figure4.5
DANGER
Mains voltage
Contact with the mains voltage presents the danger of a
deadly electric shock.
For that reason, observe the following warnings under all
circumstances:
▶
Electrical connections may only be made by a qualified
electrician.
▶
The on-site electrical installation must conform to the
applicable protective regulations (230 / 240VAC,
50 / 60Hz)!
▶
The mains plug must be disconnected before any work
is performed on the operator.
▶
Connect the mains voltage directly at the transformer
plug terminal using theNYY underground cable.
3.5 Fitting the circuit board bracket
▶
See Figure4.6
1. Fasten the circuit board bracket using the two screws
loosened earlier,
D
, as well as two additional screws
from the scope of delivery.
2. Replace the connecting terminals.
3.6 Fitting the magnet holder
▶
See Figure4.7
1. Push the gate by hand into the CLOSE end-of-travel
position.
2. Fully preassemble the magnet slide in the centre position.
3. Fit the toothed track clip so that the magnet is offset by
approx. 20mm from the reed contact in the circuit board
bracket.
3.7 Locking the operators
▶
See Figure5
The operator is engaged once locked.
▶
Turn the mechanism back to the lock position while
slightly raising the motor.
3.8 Connecting additional
components / accessories
▶
See the control print overview in Figure6
WARNING
Danger of injury due to unwanted
gate travel
Incorrectly attached control devices
(e.g.buttons) may trigger unwanted gate
travel. Persons or objects may be
trapped as a result.
▶
Install control devices at a height of
at least 1.5m (out of the reach of
children).
▶
Fit permanently installed control
devices (such as buttons, etc.)
within sight of the gate, but away
from moving parts.
Persons or objects may be trapped if the
installed safety equipment fails.
▶
In accordance with BGR232, install
at least one clearly visible and easily
accessible emergency command
unit (emergency OFF) near the gate
so the gate can be brought to a
standstill in the case of danger
(seesection3.8.3)
ATTENTION
Damage to the electronics caused by external voltage
External voltage on the connecting terminals of the control
will destroy the electronics.
▶
Do not apply any mains voltage (230 / 240VAC) to the
connecting terminals of the control.
The total consumed current may be max.500mA when
connecting accessories at the following terminals:
• 24V= • SE3 / LS
• Ext.radio • SE1 / SE2
3.8.1 Connecting an external radio receiver
▶
See Figure6.1
▶
Connect the wires of the external radio receiver as
follows:
– GN to terminal20 (0V)
– WH to terminal 21 (channel 1 signal)
– BN to terminal5 (+24V)
– YE to terminal23 (channel2 signal for partial
opening). Only with a 2-channel receiver.
NOTE:
The aerial wire of external radio receivers should not come
into contact with metal objects (nails, bracing, etc.). The best
orientation to achieve an optimum range must be established
by trial and error.
30
C300 - C800 / Rev. 1.1 RE / 07.2014
ENGLISH
… 30 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Berner C500 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info