Bedienungsanleitung Berner C500 (Seite 31 von 144) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

680440

Zoom out

Zoom in

Vorherige Seite

1/144

Nächste Seite

3.8.2 Connecting an external button*

▶

See Figure6.2

One or more buttons with normally open contacts (volt-free),

e.g. key switches, can be connected in parallel, max. lead

length 10m.

Impulse control:

▶

First contact to terminal21

▶

Second contact to terminal20

Partial opening:

▶

First contact to terminal23

▶

Second contact to terminal20

NOTE:

If auxiliary voltage is needed for an external button, then a

voltage of +24VDC is available for this at terminal5

(toterminal 20 = 0V).

3.8.3 Connecting a cut-out to stop the operator

(stopor emergency-OFF circuit)

A cut-out with normally closed contacts (switching to 0V or

volt-free) is connected as follows (see Figure6.3):

1. Remove the wire jumper inserted at the factory between

terminal12 and terminal13.

– Terminal12: STOP or emergency-OFF input

– Terminal13: 0V

2. Connect the switching output or ﬁrst contact to

terminal12 (STOP or emergency-OFF input).

3. Connect 0V (ground) or the second contact to

terminal13 (0V).

NOTE:

By opening the contact, any travel cycles in progress are

immediately halted and permanently prevented.

3.8.4 Connecting a warning lamp *

▶

See Figure6.4

A warning lamp or CLOSE limit switch reporting can be

connected via the volt-free contacts on the Option connector.

The voltage at the 24VDC connector can be used for

operation (e.g. warning signals prior to and during gate travel)

with a 24 V lamp (max. 7W).

NOTE:

A 230V warning lamp must be directly supplied with power.

3.8.5 Connecting safety / protective devices

▶

See Figures6.5 – 6.7

Safety devices such as photocells / closing edge safety

devices (SKS) or 8k2 resistance contact strips can be

connected:

SE1 in the opening direction, monitored safety device or

8k2 resistance contact strip

SE2 in the closing direction, monitored safety device or

8k2resistance contact strip

SE3 in the closing direction, photocell without testing or

dynamic 2-wire photocell, e.g. as a through-trafﬁc

photocell

The functions selected for the 3 safety circuits are set via the

DIL switches (see section5).

* Accessory, not included as standard equipment!

Terminal assignment:

Terminal 20 0V (power supply)

Terminal 18 Test signal

Terminals 71 / 72 / 73 Safety device signal

Terminal 5 +24V (power supply)

NOTE:

Safety devices without a testing unit (e.g. static photocells)

must be tested twice a year. They may only be used to

protect property!

3.8.6 Connecting universal adapter print UAP1*

▶

See Figure6.8

Connection option for the universal adapter print UAP1.

3.8.7 Connecting HNA outdoor emergency battery*

▶

See Figure6

To enable gate movement in the event of a mains failure, an

optional emergency battery can be connected. In the case of

a mains failure, the system automatically switches to battery

operation.

WARNING

Danger of injury due to unexpected gate travel

Unexpected gate travel can result when the emergency

battery is still connected despite the mains plug being

pulled out.

▶

Pull out the mains plug and the plug of the emergency

battery when performing all work on the gate system.

4 Initial operation

WARNING

Danger of injury during gate travel

If people or objects are in the area

around the gate while the gate is in

motion, this can lead to injuries or

damage.

▶

Make sure that children are not

playing near the gate system.

▶

Make sure that no persons or

objects are in the gate's travel

range.

▶

If the gate system only has one

safety feature, only operate the

sliding gate operator if you are

within sight of the gate's travel

range.

▶

Monitor the gate travel until the gate

has reached the end-of-travel

position.

▶

Only drive or pass through remote-

control gate systems when the gate

is at a standstill!

C300 - C800 / Rev. 1.1 RE / 07.2014 31

ENGLISH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Berner C500 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info