Bedienungsanleitung Berner C500 (Seite 33 von 144) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

680440

Zoom out

Zoom in

Vorherige Seite

1/144

Nächste Seite

▶

Both of the following procedures must be conducted

three times.

Force learning runs:

▶

Press circuit board buttonT once.

The operator automatically moves into the OPEN

end-of-travel position.

▶

Press circuit board buttonT once.

The operator automatically moves into the CLOSE

end-of-travel position.

4.3.1 Setting the force limit

CAUTION

Danger of injury due to the force value being set too

high

If the force value is set too high, the force limit is less

sensitive and the gate will not stop on time when closing.

This could lead to injuries and damage.

▶

Do not set a force value that is too high.

NOTE:

Due to special ﬁtting situations, it can, however, happen that

the previously taught-in forces prove inadequate, which can

lead to undesired reversing. Readjust the forces in such

cases.

The force limit of the gate system is set via a potentiometer

that is labelled "KraftF" on the control print (see Figure9.1).

1. The increase in the force limit is a percentage increase in

relation to the taught-in values where the setting of the

potentiometer denotes the following force increase:

Full left + 0 % force

Centred +15 % force

Full right +75 % force

2. The taught-in force setting must be checked using a

suitable force measuring device to make sure that the

values are permissible within the application scope of the

European Standards EN12453 and EN12445 or the

corresponding national regulations.

4.3.2 Operator speed

If the force measured with the force measuring device is still

too high when the potentiometer is turned to full left, this can

be changed by reducing the travel speed (see Figure 9.2).

Adjusting the speed:

1. Set DIL switch15 to ON.

2. Perform three successive force learning runs

(seesection4.3).

3. Check again using the force measuring device.

4.3.3 Switching off the force limit

NOTE:

Not for use in countries with EU directives!

The force limit can be switched off by snipping through the

BR1 wire jumper on the control print.

If no safety devices are connected (DIL switches3 – 6 to

OFF), the operator will only work in press-and-hold operation.

If 8k2 resistance contact strips are connected

(DILswitch3 – 6 to ON) the operator will work

in-press-and-release operation without force limit.

Deactivating the force limit:

1. Perform a factory reset (see section10).

2. Snip through the BR1 wire jumper.

3. Set DIL switch2 to ON and teach in the operator again

(see section4.2).

If the wire jumper is snipped through during set-up or during

gate travel, this will not have any effect on the function.

NOTE:

Once you have completed the teach-in procedure, the door

system can only be operated using an external button.

• A permanent contact at terminals 20 + 21 moves the

operator in the Open direction

• A permanent contact at terminals 20 + 23 moves the

operator in the Close direction

Reactivating the force limit:

1. Perform a factory reset (see section10).

2. Connect the BR1 wire jumper.

3. Set DIL switch2 to ON and teach in the operator again

(see section4.2).

4.4 Changing the starting point for slow speed

when opening and closing

The slow speed length is automatically set to a basic value of

approx. 500mm before the end-of-travel positions after the

end-of-travel positions have been taught in. The starting

points can be reprogrammed from a minimum length of

approx. 300mm up to the entire gate length (see Figure9.3).

Changing the starting points for slow speed deletes the

already taught-in forces and they must be taught in again

after the changes have been made.

Changing the starting points:

1. The end-of-travel positions must be set and the gate is in

the CLOSE end-of-travel position and DIL switch2 must

be set to OFF.

2. Set DIL switch12 to ON.

3. Press print buttonT.

The gate will travel normally in press-and-release

operation in the OPEN direction.

4. When the gate passes the desired position for the start of

slow speed, brieﬂy press print buttonP.

The operator will move at slow speed for the remaining

distance until in the OPEN end-of-travel position.

5. Press print buttonT again.

The gate will again travel normally in press-and-release

operation in the CLOSE direction.

6. When the gate passes the desired position for the start of

slow speed, brieﬂy press print buttonP.

The operator will move at slow speed for the remaining

distance until in the CLOSE end-of-travel position.

7. Set DIL switch12 to OFF.

The slow speed starting point settings have now been

completed. The green LED ﬂashes to signal that the forces

must be taught in again.

NOTE:

The starting points for slow speed can also be set to "overlap";

in this case, the entire gate movement is in slow speed.

C300 - C800 / Rev. 1.1 RE / 07.2014 33

ENGLISH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Berner C500 Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info