Bedienungsanleitung Berner C500 (Seite 34 von 144) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

680440

Zoom out

Zoom in

Vorherige Seite

1/144

Nächste Seite

4.5 Reversal limit

During operation of the gate in the CLOSE direction, the

system must distinguish between two possibilities: whether

the gate contacts the end stop (gate system stops) or an

obstruction (gate reverses direction). The limit range can be

adjusted as follows (see Figure9.4).

Setting the reversal limit:

1. Set DIL switch11 to ON.

The reversal limit can now be set step-by-step.

2. Brieﬂy press print button P to decrease the reversal limit.

Brieﬂy press print button T to increase the reversal limit.

During adjustment, the green LED will indicate the

following settings:

1× ﬂashing

up to

Minimum reversal limit, the green LED

ﬂashes once

10× ﬂashing Maximum reversal limit, the green LED

ﬂashes 10 times

3. Set DIL switch11 back to OFF to store the set reversal

limit.

4.6 Automatic timed closing

NOTE:

Automatic timed closing can only be activated if at least one

safety device has been connected. This is required according

to DINEN13241-1.

The hold-open phase can be set for operation with automatic

timed closing (see Figure 9.5).

Setting the hold-open phase:

1. Set DIL switch13 to ON.

The hold-open phase can now be set in increments.

2. Brieﬂy press print button P to decrease the hold-open

phase.

Brieﬂy press print button P to increase the hold-open

phase.

During adjustment, the green LED will indicate the

following settings:

1× ﬂashing 30 second hold-open phase

2× ﬂashing 60 second hold-open phase

3× ﬂashing 90 second hold-open phase

4× ﬂashing 120 second hold-open phase

5× ﬂashing 180 second hold-open phase

3. Set DIL switch13 back to OFF to store the set hold-

open phase.

WARNING

Danger of injuries due to faulty safety equipment

In the event of a malfunction, there is a danger of injuries

due to faulty safety equipment.

▶

After the learning runs, the person commissioning the

system must check the function(s) of the safety

equipment.

The system is ready for operation only after this.

5 DIL Switch Functions

The control is programmed via the DIL switches. Before initial

start-up, the DIL switches are in the factory settings, i.e. all

the switches are in the OFF position. Changes to the DIL

switch settings are only permissible under the following

conditions:

• The operator is at rest.

• The warning or hold-open phase is not active.

The DIL switches must be set as described below in

accordance with the national regulations, the desired safety

equipment and the on-site circumstances.

5.1 DIL switch1

Installation direction:

▶

See Figure7.1

1 ON Gate closes to the right (as viewed from the

operator)

1 OFF

Gate closes to the left (as viewed from the

operator)

5.2 DIL switch2

Set-up mode:

▶

See Figures 8.1a – c

The safety and protective devices are not active during set-up

mode.

2 ON • Teach-in gate travel

• Delete gate data

2 OFF

Normal mode

5.3 DIL switch3 / DIL switch4

SE1 safety device (opening):

▶

See Figure9.6

The functions of the SE1 are set with DIL switch3 in

combination with DIL switch4.

3 ON Activation kit for closing edge safety device or

photocell with testing

3 OFF

• 8k2 resistance contact strip

• Photocell from another manufacturer

• No safety device (8k2 resistance between

terminals20 / 72, delivery status)

4 ON Brief, immediate reversing in the CLOSE direction

(for SKS)

4 OFF

Brief, delayed reversing in the CLOSE direction

(forphotocell)

C300 - C800 / Rev. 1.1 RE / 07.2014

ENGLISH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Berner C500 Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info