Bedienungsanleitung Berner C500 (Seite 32 von 144) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

680440

Zoom out

Zoom in

Vorherige Seite

1/144

Nächste Seite

WARNING

Danger of crushing and shearing

Fingers or limbs may be crushed and severed if caught in

the toothed track or between the gate and closing edge

while the gate is in motion.

▶

Whenever the gate is moving, never touch the toothed

track, toothed wheel, and the main or secondary

closing edges.

4.1 Preparation

▶

Before initial start-up, check that all the connecting leads

are correctly installed at the connecting terminals.

▶

Make sure that all DIL switches are set to the factory

setting (OFF) (see Figure7), the gate is half open and the

operator engaged.

Change the following DIL switches:

▶

DIL switch1: Installation direction (see Figure7.1)

– To ON, if the gate closes towards the right.

– To OFF, if the gate closes towards the left.

▶

DIL switches3-7: Safety devices

(seeFigures9.6 / 9.7 / 9.8)

– Set according to the connected safety and protective

devices (see section 5.3 – 5.5). These are, however,

not active during set-up mode.

4.2 Teaching in the gate's end-of-travel positions

4.2.1 Recording the CLOSE end-of-travel position

▶

See Figure8.1a

The limit switch (reed contact) must be connected before

teaching in the end-of-travel positions. The limit switch wires

must be connected at the REED terminal.

The option relay has the same function as the red LED during

set-up. The limit switch position can be viewed from afar with

a connected lamp (seeFigure6.4).

Teaching in the CLOSE end-of-travel position:

1. Open the gate halfway.

2. Set DIL switch2 (set-up mode) to ON.

The green LED slowly ﬂashes, the red LED remains lit.

3. Press circuit board button T and keep it pressed.

The gate now travels in CLOSE direction at slow speed.

The gate stops once the limit switch has been reached.

4. Immediately release circuit board buttonT.

The red LED goes out.

The gate is now in the CLOSE end of travel position.

NOTE:

If the gate travels in the opening direction, DIL switch1 is in

the wrong position and must be reset. Then repeat steps 1to4.

If the position of the gate does not correspond to the desired

CLOSE position, a readjustment must be made.

Readjusting the CLOSE end-of-travel position:

1. Adjust the position of the magnet by moving the magnet

slide.

2. Press circuit board buttonT until the gate reaches the

readjusted end-of-travel position and the red LED goes

out.

3. Repeat steps 1 + 2 until the desired end-of-travel

position has been reached.

4.2.2 Recording the OPEN end-of-travel position

▶

See Figure8.1b

Teaching in the OPEN end-of-travel position:

4. Press circuit board button T and keep it pressed.

The gate now travels in OPEN direction at slow speed.

5. Release circuit board buttonT, once the desired OPEN

end-of-travel position is reached.

6. Press circuit board button P to conﬁrm this position.

The green LED ﬂashes rapidly for 2seconds to indicate

that the OPEN end-of-travel position has been recorded

and then goes out.

4.2.3 Recording the partial opening end-of-travel

position

▶

See Figure8.1c

NOTE:

If press-and-hold operation has been set, it is not possible to

record the partial opening end-of-travel position.

Teaching in the partial opening end-of-travel position:

1. Press circuit board buttonT and keep it pressed to move

the gate back towards the CLOSE position.

The green LED will ﬂash slowly.

2. Release circuit board button T once the desired partial

opening end-of-travel position is reached.

3. Press circuit board button P to conﬁrm this position.

The green LED ﬂashes rapidly for 2seconds to indicate

that the partial opening end-of-travel position has been

recorded and then goes out.

4.2.4 Ending the set-up-mode

▶

After you have ﬁnished the teach-in procedure, set

DILswitch2 back to OFF.

The green LED signals that forces must be taught in by

ﬂashing quickly.

The safety equipment is active again.

4.2.5 Reference run

▶

See Figure8.2

After teaching in the end-of-travel positions, the ﬁrst cycle is

always a reference run. During this reference run the option

relay clocks and a connected warning lamp ﬂashes.

Reference run to CLOSE end-of-travel position:

▶

Press circuit board buttonT once.

The operator automatically moves into the CLOSE

end-of-travel position.

▶

If press-and-hold operation has been set (DIL switch16

to ON), press and hold circuit board buttonT until the

gate is in the close end-of-travel position.

NOTE:

Initial start-up is now ﬁnished if press-and-hold operation has

been set (DIL switch16 to ON).

4.3 Learning the forces

Once the end-of-travel positions have been taught in and the

reference run performed, force learning runs must also be

performed. For this, three successive gate cycles must take

place, during which none of the safety devices may be

activated. Recording the forces takes place automatically by

press-and-release operation in both directions and the option

relay clocks. The green LED ﬂashes throughout. This LED is

steadily illuminated once the force learning runs have been

completed (see Figure9.1).

C300 - C800 / Rev. 1.1 RE / 07.2014

ENGLISH

Berner C500 Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info