680440

Berner C500 Seite 37

37
Zoom out
Zoom in
Vorherige Seite
1/144
Nächste Seite
6.2 Radio Remote Control
6.2.1 External radio receiver
Plug-in the external radio receiver on the respective
connector (see Figure 6.1). The function “impulse” (Open –
Stop – Close – Stop) and the function “partial opening” for at
max. 60 different hand transmitters can be programmed on
the external radio receiver. If more than 60 different hand
transmitters are programmed the receiver deletes those that
have been registred in the beginning.
6.3 Programming the hand transmitter buttons on
an external radio receiver
6.3.1 Assigning a button function for channel 1
1. Briefly press the P button (programming button) on the
receiver. The LED will begin to light up.
2. Press the desired button on the hand transmitter for at
least three seconds until the LED goes out.
3. Release the button.
4. The receiver is ready to receive.
The function of this hand transmitter button is now
programmed on the receiver (see Figure 11a).
6.3.2 Assigning a button function for channel 2
1. Briefly press the P button (programming button) on the
receiver. The LED will begin to light up.
2. Press the P button again. The LED will go out and then
light up again.
3. Press the desired button on the hand transmitter for at
least three seconds until the LED goes out.
4. Release the button.
5. The receiver is ready to receive.
The function of this hand transmitter button is now
programmed on the receiver (see Figure 11b).
6.4 Operation
At least one hand transmitter button must be taught in on the
radio receiver to operate the sliding gate operator via radio.
During radio transmission, the hand transmitter and receiver
must be at least 1 m apart.
6.5 Deleting all data of an external radio receiver
1. Press the P button on the receiver for
approx.10seconds. The LED will flash.
2. Wait until the flashing stops, and release the button.
Alltaught-in hand transmitters are now deleted.
NOTE:
It is not possible to delete individual hand transmitters.
7 Final Work
▶
Replace the transparent cover (see Figure12) and close
the housing cover after completing all of the steps
required for initial start-up.
7.1 Fixing the warning sign
▶
See Figure13
▶
Fix the sign warning about getting trapped in a
noticeable, cleaned and degreased place, for example,
near to the permanently installed button for moving the
operator.
8 Operation
WARNING
Danger of injury during gate travel
If people or objects are in the area
around the gate while the gate is in
motion, this can lead to injuries or
damage.
▶
Make sure that children are not
playing near the gate system.
▶
Make sure that no persons or
objects are in the gate's travel
range.
▶
If the gate system only has one
safety feature, only operate the
sliding gate operator if you are
within sight of the gate's travel
range.
▶
Monitor the gate travel until the gate
has reached the end-of-travel
position.
▶
Only drive or pass through remote-
control gate systems when the gate
is at a standstill!
WARNING
Danger of crushing and shearing
Fingers or limbs may be crushed and severed if caught in
the toothed track or between the gate and closing edge
while the gate is in motion.
▶
Whenever the gate is moving, never touch the toothed
track, toothed wheel, and the main or secondary
closing edges.
8.1 Instructing users
▶
All persons using the gate system must be shown how to
operate it properly and safely.
▶
Demonstrate and test the mechanical release as well as
the safety return.
8.2 Function check
1. To check the safety reversal, stop
the gate with both hands while it is
closing.
The gate system must stop and
initiate the safety reversal.
2. Proceed in the same manner while
the gate is opening.
The gate system must stop and
reverse briefly.
▶
In the event of a failure of the safety reversal, a specialist
must be commissioned immediately for the inspection
and repair work.
C300 - C800 / Rev. 1.1 RE / 07.2014 37
ENGLISH
… 37 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Berner C500 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info