680440
39
Zoom out
Zoom in
Vorherige Seite
1/144
Nächste Seite
Display flashes 3×
Error / warning
Force limit in CLOSE direction
Possible cause
Obstruction in gate area
Remedy
Remove the obstruction; check forces, increase ifnecessary
Display flashes 4×
Error / warning
Hold or static current circuit is open, operator at a standstill
Possible cause
• Normally closed contact at terminal 12 / 13 is open
• Electric circuit interrupted
Remedy
• Close contact
• Check electric circuit
Display flashes 5×
Error / warning
Force limit in OPEN direction
Possible cause
Obstruction in gate area
Remedy
Remove the obstruction; check forces, increase ifnecessary
Display flashes 6×
Error / warning
System error
Possible cause
Internal error
Remedy
Perform a factory reset (see section10) and teach in the
control again (see section4.2), or exchange it if necessary
Display flashes 7×
Error / warning
Peak force
Possible cause
• Motor blocked
• Force cut-out has not responded
Remedy
Check the motor for seizure
10.4 Error acknowledgement
If an error occurs, this can be acknowledged, provided the
error is no longer present.
Actuate an internal or external impulse generator.
The error is deleted and the gate travels in the
corresponding direction.
11 Resetting the Control / Restoring
Factory Settings
To reset the control (taught-in end-of-travel positions,
forces):
1. Set DIL switch2 to ON.
2. Immediately press circuit board buttonP briefly.
3. When the red LED flashes rapidly, DIL switch2 must be
quickly set to OFF.
The control system has now been reset to the factory setting.
12 Dismantling and Disposal
NOTE:
When disassembling, observe the applicable regulations
regarding occupational safety.
Have a specialist dismantle the sliding gate operator in the
reverse order of these fitting instructions and dispose of it
properly.
13 Optional Accessories
Optional accessories are not included in the scope of delivery.
Loading of the operator by all electrical accessories:
max.500mA.
The following accessories, among others, are available:
• External radio receivers
• External impulse buttons (e.g. key switch)
• External code and transponder switches
• One-way photocell
• Warning lamps / warning lights
• Photocell expanders
• Universal adapter print UAP1
• HNA outdoor emergency battery
• Further accessories available on request
C300 - C800 / Rev. 1.1 RE / 07.2014 39
ENGLISH
39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Berner C500 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info