Bedienungsanleitung Black Decker BCD003 (Seite 6 von 88) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

709448

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

ENGLISH

(Original instructions)

u If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised BLACK+DECKER Service

Centre in order to avoid a hazard.

Features

This tool includes some or all of the following features.

1. Variable speed switch

2. Forward/reverse slider

3. Torque adjustment collar

4. Keyless chuck

5. Dual range gearing

6. LED work light

7. Battery

8. Battery release button

Assembly

Use

Warning! Let the tool work at its own pace. Do not overload.

Charging the battery (g. A1, A2)

The battery needs to be charged before rst use and whenev-

er it fails to produce sufcient power on jobs that were easily

done before. The battery may become warm while charging;

this is normal and does not indicate a problem.

Warning! Do not charge the battery at ambient temperatures

below 10 °C or above 40 °C. Recommended charging tem-

perature: approx. 24 °C.

Note: The charger will not charge a battery if the cell

temperature is below approximately 10 °C or above 40 °C.

The battery should be left in the charger and the charger

will begin to charge automatically when the cell tempera-

ture warms up or cools down.

u Plug the charger (9) into any standard 230 Volts 50 Hz

electrical outlet.

u Slide the battery pack (7) into the charger as shown in g.

A1, A2.

The LED (9a) will ash indicating that the

battery is being charged.

The completion of charge is indicated by the

LED (9a) remaining on continuously. The pack

is fully charged and may be used at this time

or left on the charger.

Warning! re Hazard. When removing the battery from the

charger, be sure to unplug the charger from the outlet rst,

then remove the battery from the charger.

Charger diagnostics

This charger is designed to detect certain problems that can

arise with the battery packs or the power source. Problems

are indicated by one LED ashing in different patterns.

Bad battery

The charger can detect a weak or damaged

battery. The LED ashes in the pattern indi-

cated on the label. If you see this bad battery

blink pattern, do not continue to charge the battery. Return it

to a service center or a collection site for ecycling.

Hot/cold pack delay

When the charger detects a battery that

is excessively hot or excessively cold, it

automatically starts a Hot/Cold Pack Delay,

suspending charging until the battery has normalized. After

this happens, the charger automatically switches to the Pack

Charging mode. This feature ensures maximum battery life.

The light ashes in the pattern indicated on the label.

Leaving the battery in the charger

The charger and battery pack can be left connected with

the LED glowing indenitely. The charger will keep the

battery pack fresh and fully charged. This charger features

an automatic tune-up mode which equals or balances the

individual cells in the battery pack to allow it to function at

peak capacity. Battery packs should be tuned up weekly or

whenever the battery no longer delivers the same amount

of work. To use the automatic tune-up mode, place the

battery pack in the charger and leave it for at least 8 hours.

Important charging notes

u Longest life and best performance can be obtained if

the battery pack is charged when the air temperature is

between 18 ° – 24 °C. DO NOT charge the battery pack in

an air temperature below +4.5 °C), or above +40 °C.

This is important and will prevent serious damage to the

battery pack.

u The charger and battery pack may become warm to the

touch while charging. This is a normal condition, and

does not indicate a problem. To facilitate the cooling of

the battery pack after use, avoid placing the charger or

battery pack in a warm environment such as in a metal

shed or an uninsulated trailer.

u If the battery pack does not charge properly:

u Check operation of receptacle by plugging in a lamp

or other appliance;

u Check to see if receptacle is connected to a light

switch which turns power off when you turn out

the lights;

u Move the charger and battery pack to a location

where the surrounding air temperature is

approximately 18 ° – 24 °C;

u If charging problems persist, take the tool, battery

pack and charger to your local service center.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker BCD003 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info