Bedienungsanleitung Black Decker BCD003 (Seite 8 von 88) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

709448

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

ENGLISH

(Original instructions)

u Run the drill very slowly, using light pressure, until

the hole is started enough to keep the drill bit from slipping

out of it.

u Apply pressure in a straight line with the bit. Use enough

pressure to keep the bit biting but not so much as to stall

the motor or deect the bit.

u Hold the drill rmly with two hands to control its twisting

action.

u DO NOT CLICK THE TRIGGER OF A STALLED DRILL

OFF AND ON IN AN ATTEMPT TO START IT. DAMAGE

TO THE DRILL CAN RESULT.

u Minimize stalling on breakthrough by reducing pressure

and slowly drilling through the last part of the hole.

u Keep the motor running while pulling the bit out of a drilled

hole. This will help reduce jamming.

u Make sure switch turns drill on and off.

Drilling in wood

Holes in wood can be made with the same twist drill bits used

for metal or with spade bits. These bits should be sharp and

should be pulled out frequently when drilling to clear chips

from the utes.

Drilling in metal

Use a cutting lubricant when drilling metals. The exceptions

are cast iron and brass which should be drilled dry. The cutting

lubricants that work best are sulfurized cutting oil or lard oil.

Drilling in masonry

For drilling in masonry, set the collar (3) to the hammer

drilling position by aligning the symbol with the marking.

Slide the speed selector (5) towards the front of the tool

(2nd gear).

Screwdriving

u Always use the correct type and size of screwdriver bit.

u If screws are difcult to tighten, try applying a small

amount of washing liquid or soap as a lubricant.

u Always hold the tool and screwdriver bit in a straight line

with the screw

Troubleshooting

Problem Possible cause Possible solution

Unit will not start. Battery pack not

charged.

Check battery pack charg-

ing requirements

Battery pack will not

charge.

Charger not plugged

in.

Surrounding air

temperature too hot or

too cold.

Plug charger into a work-

ing outlet.

Move charger and battery

pack to a surrounding air

temperature of above 40

degrees F (45ºC) or below

105 degrees F (+40.5ºC)

Problem Possible cause Possible solution

Unit shuts off

abruptly.

Battery pack has

reached its maximum

thermal limit.

Out of charge. (To

maximize the life of

the battery pack it is

designed to shutoff

abruptly when the

charge is depleted

Allow battery pack to cool

down.

Place on charger

and allow to charge.

Maintenance

Your BLACK+DECKER tool has been designed to operate

over a long period of time with a minimum of maintenance.

Continuous satisfactory operation depends upon proper tool

care and regular cleaning.

Your charger does not require any maintenance apart from

regular cleaning.

Warning! Before performing any maintenance on the tool,

remove the battery from the tool. Unplug the charger before

cleaning it.

u Regularly clean the ventilation slots in your tool and

charger using a soft brush or dry cloth.

u Regularly clean the motor housing using a damp cloth.

Do not use any abrasive or solvent-based cleaner.

u Regularly open the chuck and tap it to remove any dust

from the interior.

Protecting the environment

Separate collection. Products and batteries

marked with this symbol must not be disposed

of with normal household waste.

Products and batteries contain materials that can be recov-

ered or recycled, reducing demand for raw materials.

Please recycle electrical products and batteries accord-

ing to local provisions. Further information is available at

www.2helpU.com

Technical data

BCD003

Voltage V

No-load speed Min

-1

0 - 360/0 - 1400

Max. torque Nm 45

Chuck capacity mm 1-10

Max Drilling capacity

Steel/wood/Masonary mm 10/25/10

Weight kg 0.9 (with battery 1.3)

Charger 90589867 90590287-06 90634971

Input voltage V

230 230 230

Output voltage V

18 18 18

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker BCD003 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info