Bedienungsanleitung Black Decker BCD003 (Seite 7 von 88) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

709448

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

ENGLISH

(Original instructions)

u The battery pack should be recharged when it fails to

produce sufcient power on jobs which were easily

done previously. DO NOT CONTINUE to use under these

conditions. Follow the charging procedure. You may also

charge a partially used pack whenever you desire with no

adverse effect on the battery pack.

u Foreign materials of a conductive nature such as, but

not limited to, grinding dust, metal chips, steel wool,

aluminum foil, or any buildup of metallic particles

should be kept away from charger cavities. Unplug the

charger before attempting to clean.

u Do not freeze or immerse the charger in water or any

other liquid.

Installing and removing the battery pack from the

tool (g. B)

Warning! Make certain the lock-off button (2) is engaged to

prevent switch actuation before removing or installing battery.

To install battery pack:

u Insert battery pack (7) into tool, until an audible click is

heard (g. B)

Removing the battery pack from the tool (g. C)

u Depress the battery release button (8) as shown in (g. C)

and pull battery pack out of tool.

Operating Instructions

Trigger switch & reversing button (g. D)

u The drill is turned ON and OFF by pulling and releasing

the trigger switch (1). The farther the trigger is depressed,

the higher the speed of the drill.

u A forward/reverse control button (2) determines the direc-

tion of the tool and also serves as a lock off button.

u To select forward rotation, release the trigger switch and

depress the forward/reverse control button to the left.

u To select reverse, depress the forward/reverse control

button the opposite direction.

Note: The center position of the control button locks the tool

in the off position. When changing the position of the control

button, be sure the trigger is released.

Torque control (g.E)

This tool is tted with a torque adjustment collar (3) to select

the operating mode and to set the torque for tightening

screws. Large screws and hard workpiece materials require

a higher torque setting than small screws and soft workpiece

materials.

u For drilling in wood, metal and plastics, set the collar to

the drilling position symbol

u For screwdriving, set the collar to the desired setting. If you

do not yet know the appropriate setting, proceed as

follows:

u Set the collar to the lowest torque setting.

u Tighten the rst screw.

u If the clutch ratchets before the desired result is achieved,

increase the collar setting and continue tightening the

screw. Repeat until you reach the correct setting. Use this

setting for the remaining screws.

Keyless chuck (g. F)

Warning! Make certain the lock-off button (2) is engaged to

prevent switch actuation before installing or removing acces-

sories.

To insert a drill bit or other accessory:

u Grasp the rear half of the chuck (4) with one hand and use

your other hand to rotate the front half in the counterclock-

wise direction, as viewed from the chuck end.

u Insert the bit or other accessory fully into the chuck, and

tighten securely by holding the rear half of the chuck and

rotating the front portion in the clockwise direction as

viewed from the chuck end.

Warning! Do not attempt to tighten drill bits (or any other ac-

cessory) by gripping the front part of the chuck and turning the

tool on. Damage to the chuck and personal injury may occur

when changing accessories.

Dual range gearing (Figure G)

The dual range feature of your drill allows you to shift gears

for greater versatility. To select low speed, high torque setting

(position 1), turn tool off and permit to stop. Slide gear shifter

button (5) away from the chuck. To select the high speed, low

torque setting (position 2), turn tool off and permit to stop.

Slide gear shifter button towards the chuck.

Note: Do not change gears when tool is running. If you are

having trouble changing gears, make sure that the dual range

gear button is either completely pushed forward or completely

pushed back.

Drilling/screwdriving

u Select forward or reverse rotation using the forward/re-

verse slider (2).

u To switch the tool on, press the switch (1). The tool speed

depends on how far you press the switch.

u To switch the tool off, release the switch.

Hints for optimum use

Drilling

u Use sharp drill bits only.

u Support and secure work properly, as instructed in the

Safety Instructions.

u Use appropriate and required safety equipment, as

instructed in the Safety Instructions.

u Secure and maintain work area, as instructed in the

Safety Instructions.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker BCD003 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info