Bedienungsanleitung Black Decker GKC1825L20 T1 (Seite 10 von 16) (Englisch)

585836

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

ENGLISH

(Original instructions)

Features

1. On/off switch

2. Lock-off button

3. Oil cap

4. Front guard

5. Chain tension adjustment ring

6. Chain

7. Guide bar

8. Chain sheath

9. Chain adjust locking knob

10. Chain cover assembly

11. Oil level indicator

12. Battery

Assembly

Warning! Always wear protective gloves when

working on your chainsaw.

Warning! Before performing any assembly

or maintenance on power tools, switch off and

remove the battery.

Warning! Remove the cable tie that attaches

the chain to the chainbar before assembly.

u A).

u Turn the tension adjust ring (5) anti-clockwise as far as it

will go so the arrow on the tension adjust ring (5) lines up

u Place the chain (6) over the guide bar (7) making sure that

the saw chain cutters on the upper part of the guide bar

u Guide the chain (6) around the guide bar (7) and pull it to

create a loop to one side at the rear end of the guide bar

(7).

u Guide the chain (6) around the drive sprocket (14). Place

G).

u Place the chain cover assembly (10) onto the chainsaw

u Turn the chain adjust locking knob (9) clockwise to attach

u Turn the chain adjust locking knob (9) 180 degrees anti-

u Turn the chain tension adjust ring (5) clockwise until the

chain (6) is tight. Make sure that the chain (6) is snug

u Check the tension as described below. Do not overtighten.

u Tighten the chain adjust locking knob (9) (L).

Before use and after every 10 minutes of use, you must check

the chain tension.

u Remove the battery (12).

u The

tension is correct when the chain (6) snaps back after

being pulled 3 mm away from the guide bar (7). There

should be no "sag" between the guide bar (7) and the

chain (6) on the underside.

Note: Do not over-tension the chain as this will lead to

excessive wear and will reduce the life of the guide bar and

the chain.

Note: When the chain is new, check the tension frequently

use because a new chain stretches slightly.

u Turn the chain adjust locking knob (9) 180 degrees anti-

u Tension the chain using the chain tension adjusting ring

u T

Chargers

u Use your BLACK+DECKER charger only to charge the

battery in the tool with which it was supplied. Other batter-

ies could burst, causing personal injury and damage.

u Never attempt to charge non-rechargeable batteries.

u Have defective cords replaced immediately.

u Do not expose the charger to water.

u Do not open the charger.

u Do not probe the charger.

The charger is intended for indoor use only.

Read the instruction manual before use.

Electrical safety

Your charger is double insulated; therefore no

earth wire is required. Always check that the

mains voltage corresponds to the voltage on the

rating plate. Never attempt to replace the charger

unit with a regular mains plug.

u If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker GKC1825L20 T1 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker GKC1825L20 T1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info