Bedienungsanleitung Black Decker GKC1825L20 T1 (Seite 12 von 16) (Englisch)

585836

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

ENGLISH

(Original instructions)

u Do not attempt to fell trees where the tree diameter is

greater than the cutting length of the chainsaw.

u Cut a direction notch to determine the direction of fall.

u Make a horizontal cut to a depth of between 1/5th and

1/3rd of the diameter of the tree, perpendicular to the line

and make a notch of about 45°.

u Make a single horizontal felling cut from the other side 25

Q). Do not cut through to the direction notch, you could

lose control of the direction of fall.

u Drive a wedge or wedges into the felling cut to open it and

Pruning trees

Make sure that there are no local by-laws or regulations that

would prohibit or control the pruning of the tree limbs. Pruning

should only be undertaken by experienced users there is an

increased risk of the saw chain pinching and kick back.

Before pruning consideration should be given to

conditions affecting the direction of fall including:

u The length and weight of the branch to be cut.

u Any unusual heavy limb structure or decay.

u Surrounding trees and obstacles including overhead.

u The wind speed and direction.

u The branch being intertwined with other branches.

The operator should consider access to the tree limb and the

direction of fall. The tree branch is liable to swing towards

the tree trunk. In addition to the user bystanders, objects and

property below the branch will be at risk.

u T -

tion to a maximum depth of one third the diameter of the

branch.

How you should cut depends on how the log is supported.

Use a saw horse whenever possible. Always start a cut with

the saw chain running and the spiked bumper (20) in contact

tion of the spiked bumper against the wood.

When supported along its whole length:

u Make a downward cut, but avoid cutting the earth as this

will blunt your saw chain quickly.

When supported at both ends:

u First, cut one third down to avoid splintering and second,

When supported at one end:

u First cut one third up to avoid splintering and second, cut

down to prevent splintering.

When on a slope:

u Always stand on the uphill side.

u Secure the workpiece using chocks or wedges. The user

or a bystander should not steady the log by sitting or

standing on it. Make sure that the saw chain does not

contact the ground.

This is strongly recommended whenever possible.

u Position the log in a stable position. Always cut on the

outside of the saw horse arms. Use clamps or straps to

secure the workpiece.

Removing the branches from a fallen tree. When limbing,

leave larger lower limbs to support the log off the ground.

Remove the small limbs in one cut. Branches under tension

should be cut from the bottom of the branch towards the top to

avoid binding the chain saw.

Trim limbs from opposite side keeping tree stem between you

and saw. Never make cuts with saw between your legs or

straddle the limb to be cut.

Pre-plan a safe exit from falling trees or branches. Make sure

that the exit route is clear of obstacles that would prevent or

hinder movement. Remember that wet grass and freshly cut

bark is slippery.

Inexperienced users should not attempt to fell trees. The user

may suffer injury or cause damage to property as a result of

failure to control the direction of fall, the tree may splinter or

damaged/dead branches may fall during cutting.

The safe distance between a tree to be felled and bystanders,

buildings and other objects is at least 2 1/2 times the height of

the tree. Any bystander, building or object within this distance

is at risk from being struck by the tree when felled.

Before attempting to fell a tree:

u Make sure that there are no local by-laws or regulations

that would prohibit or control the felling of the tree.

u Consider all conditions that may affect the direction of fall,

including:

u The intended direction of fall.

u The natural lean of the tree.

u Any unusual heavy limb structure or decay.

u Surrounding trees and obstacles including overhead

lines and underground drains.

u The wind speed and direction.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker GKC1825L20 T1 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker GKC1825L20 T1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info