Bedienungsanleitung Black Decker GL340 (Seite 9 von 16) (Englisch)

527583

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

‘female’ connector ‘male’ connector

Warning! Never wire an extension cable with

anything other than the ‘female’ connector

supplied and a 13 amp BS1363A approved

plug with the recommended fuse. Never

wire a ‘male’ connector to your extension

cable and never wire an extension cable

with a plug of any kind at each end of the

cable. This is extremely dangerous and

results in the pins being live which may

cause a fatal electric shock.

Fitting the ‘female’ connector

(UK only)

To remove the cover, unscrew the fixing screw until it

is free of the nut which is located in the hexagonal

recess on the underside of the connector. Take care

not to lose the nut if it falls out. There is no need to

completely remove the fixing screw as it is intended

to remain captive in the cover. The cover can now be

removed by applying pressure as shown below.

apply pressure here

The extension cable contains two wires which are

colour coded for easy recognition; brown is for ‘Live’

(L) and blue is for ‘Neutral’ (N). The female connector

is marked ‘L’ for live and ‘N’ for neutral. These

markings are located inside the body near the

terminal screws (see opposite, figure a). With the

connector cover removed, lift out the cable protector

and proceed as follows:

• Pass the cable through from the narrow end of

the cable protector (see opposite, figure a).

• Prepare the cable ends to the specified strip

lengths (see opposite, figure b).

Existing cable systems (UK only)

If you already own an outdoor cable system, we

recommend that you replace the existing ‘female’

cable connector with the new ‘female’ connector

(see below) which is supplied loose in the carton.

(Please read the section entitled “Fitting the ‘female’

connector”.)

old ‘female’ connector new ‘female’ connector

Should you wish to convert more than one cable

system, the new female connector is available as an

accessory from most major DIY retail outlets and from

Black & Decker service agents (cat. no. A6624S).

Existing powered garden tools

(UK only)

To connect existing Black & Decker garden power

tools to the new system you will require an adaptor

(see below). This is available as an accessory from

most major DIY retail outlets (cat. no. A6623S).

Warning! This adaptor is only suitable for

products rated up to 500W.

It is not recommended for use with the

following:

Hover mowers

Rotary mowers with grass collection

Chainsaws

Shredders

Blowervacs.

Please contact your local service agent

should you require further advice.

Fitting your own extension cable

(UK only)

• When fitting your own extension cable fit a

13 amp plug (see “Fitting the mains plug”) to one

end of the cable and a ‘female’ connector

(supplied loose in the carton) to the other end

(see opposite). For wiring instructions see the

following sections.

• A ‘male’ connector is already attached to the

electrical supply cable on your mower and is

designed to be non-rewireable (see opposite).

This should not be removed. Should the

cable and plug become damaged or need

replacing, please return your mower to your local

Black & Decker service agent.

ENGLISH

GL340 UK p02-11 w/p 24/3/00, 2:17 pm5

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker GL340 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info