Bedienungsanleitung Black Decker GL652 T3 (Seite 8 von 84) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

583276

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

ENGLISH

Fittinganewspoolofcuttingline(g.G&H)

Replacement spools of cutting line are available from your

Black & Decker dealer (cat. no. A6441). Complete cassettes

containing a spool of cutting line are also available

(cat. no. A6442).

u Unplug the tool.

u Keep the tabs (17) depressed and remove the spool cover

(18) from the housing (11) (g. G).

u Remove the empty spool (19) from the spool cover.

u Remove any dirt and grass from the spool cover and

housing.

u Take the new spool and push it onto the boss in the spool

cover. Rotate the spool slightly until it is seated.

u Unclip the end of one of the cutting lines and guide the

line into one of the eyelets (20) (g. H). The line should

protrude approx. 11 cm from the spool cover.

u Unclip the end of the other cutting line and guide the line

into the other eyelet. The line should protrude approx.

11 cm from the spool cover.

u Align the tabs (17) on the spool cover with the cut outs

(21) in the housing (g. G).

u Push the cover onto the housing until it snaps securely

into place.

Warning! If the cutting lines protrude beyond the trimming

blade (10), cut them off so that they just reach the blade.

Windingnewlineontoanemptyspool(g.I,J&K)

You may wind new cutting line onto an empty spool.

Replacement packs of cutting line are available from your

Black & Decker dealer (cat. no. A6440).

u Remove the empty spool from the tool as described above.

u Remove any remaining cutting line from the spool.

u First wind new line onto the uppermost part of the spool:

- Feed 2 cm of cutting line into one of the slots in the

upper section of the spool as shown.

- Wind the cutting line onto the spool in the direction of

the arrow. Make sure to wind the line on neatly and in

layers. Do not criss-cross.

- When the wound cutting line reaches the recesses (23),

cut the line.

- Temporarily park the line in the slots (22) on one side of

the spool as shown.

u Repeat the above procedure for the second cutting line on

the lower section of the spool. Park the line in the unused

slots (22).

u Proceed as described above to t the spool on the tool.

Do not forget to release the cutting line from the parking

slots (22).

Warning! Only use the appropriate type of Black & Decker

cutting line. Ensure that cutting line is present in both sections

of the spool (g. K).

Mainsplugreplacement(U.K.&Irelandonly)

If a new mains plug needs to be tted:

u Safely dispose of the old plug.

u Connect the brown lead to the live terminal in the new plug.

u Connect the blue lead to the neutral terminal.

Warning! No connection is to be made to the earth terminal.

Follow the tting instructions supplied with good quality plugs.

Recommended fuse: 5 A.

Troubleshooting

If your tool seems not to operate properly, follow the

instructions below. If this does not solve the problem,

please contact your local Black & Decker repair agent.

Warning! Before proceeding, switch off and unplug the tool.

Tool runs slowly

u Check that the spool housing can rotate freely.

Carefully clean it if necessary.

u Check that the cutting line does not protrude more than

11 cm from the spool housing. If it does, cut it off so that it

just reaches the line trimming blade.

Automatic line feed does not work

u Keep the tabs depressed and remove the spool cover

from the housing.

u Pull the cutting line until it protrudes 11 cm from the

housing. If insufcient cutting line is left on the spool,

install a new spool of cutting line as instructed above.

u Align the tabs on the spool cover with the cut outs in the

housing.

u Push the cover onto the housing until it snaps securely

into place.

u If the cutting line protrudes beyond the trimming blade,

cut it off so that it just reaches the blade.

If the automatic line feed still does not work or the spool is

jammed, try the following suggestions:

u Carefully clean the spool cover and housing.

u Remove the spool and check if the lever can move freely.

u Remove the spool and unwind the cutting line, then wind it

on neatly again as described above. Replace the spool as

instructed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker GL652 T3 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info