Bedienungsanleitung Black Decker HVLP400 T1 (Seite 9 von 16) (Englisch)

578633

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

ENGLISH

(Original instructions)

Note: Ensure that the locking ring is tight and that the side ll

canister is rmly secured in place.

Aligning the pickup tube (g. B & C)

The pickup tube can be aligned in the direction that you will be

doing the most spraying to help minimize the amount of times

that you will have to rell the canister.

u If you are spraying at an upward angle or straight on,

position the pickup tube (g. B) toward the back of the

canister.

u If you are spraying at a downward angle, position the

pickup tube (g. C) toward the front of the canister.

This will ensure you spray as much material as possible

before you need to rell.

Attaching the air hose (g. D & E)

u Insert one end of the air hose (5) into the back of the

sprayer (3). A slight twisting action when inserting the

hose will help ensure a snug t.

u Insert the other end of the air hose (5) into the back of the

power unit (4). A slight twisting action when inserting the

hose will help ensure a snug t.

Filling the canister (g. F)

u Check to make sure that the side ll canister (6) is com-

pletely screwed onto the sprayer.

u Lay the sprayer on its side with the canister side lid facing

up.

u Pour the properly thinned and strained material to be

sprayed into the side ll canister.

Note : Use the mixing bucket provided to pour material from

the original material container into the side ll canister.

u Clean any residual liquid from the threads or sides of the

canister and sprayer.

u Starting the threads evenly, screw the lid completely

onto the side ll canister. Check the lid to make sure it is

threaded on squarely and completely before picking up

the sprayer.

Use

Switching on and off (g. G)

The on/off switch is located on the handle of the power unit.

u To turn the power unit on, press the top of switch (I).

u To turn the power unit off, press the bottom of switch (0).

Warning! Never point the sprayer at any part of the body.

Never pull the trigger while adjusting the spray setting.

Selecting the spray pattern (g. H & I)

This sprayer is tted with a pattern select nozzle (10) which is

capable of 3 spray patterns. This is used to select the correct

spray pattern for your particular spraying operation.

Using the pattern select nozzle (10), choose from one of the

following applications:

Horizontal Flat Jet - Apply up and down a surface.

Circular Jet - for corners, edges and narrow surfaces.

Vertical Flat Jet. Apply side to side.

There are three spray patterns to choose from. They are

marked as 1, 2 and 3 on the pattern select label located on

the top of the sprayer (g. H)

u To select the required spray pattern, turn the pattern select

nozzle (10) and align the green indicator on the pattern

select nozzle (10) with the number on the label (g. I)

Warning! Never point the sprayer at any part of the body.

Never pull the trigger while adjusting the spray setting.

Flow control knob (g. J)

The ow control knob regulates the amount of liquid that can

be sprayed.

u Turn the ow control knob (8) clockwise to increase the

ow of liquid

u Turn the ow control knob (8) counterclockwise to

decrease the ow of liquid.

u The ow indicator (9) on the top of the sprayer moves

forward (minimal liquid ow) and backward (maximum

liquid ow) as the ow control knob (8) is turned.

Note : Always test the spray pattern on scrap cardboard

or similar material rst. Begin with ow control knob on the

highest ow setting. If less ow is desired, dial the ow control

knob in. Heavier, thicker materials should be sprayed with the

indicator close to the (+) icon. Thinner materials should be

sprayed with the indicator close to the (-) icon.

Note : If the ow control setting is set completely to the

minimum side, the trigger will have limited or no travel. Back

the ow control knob off (clockwise) to allow for more trigger

travel.

Liquid material preparation (g. K & L)

Note : Make sure the type of material you use can be cleaned

with either mineral spirits or paint thinner (for oil-based paints)

or a warm water and soap solution (for water soluble paints

like latex). Use drop cloths to protect your oors and anything

else in the spraying area that you wish to remain untouched.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker HVLP400 T1 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker HVLP400 T1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info