Bedienungsanleitung Black Decker HVLP400 T1 (Seite 10 von 16) (Englisch)

578633

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

ENGLISH

(Original instructions)

The liquid being sprayed may need to be thinned (diluted)

before staring. When thinning, use the proper liquid thinner

recommended on the container by the material manufacturer.

Warning! Do not use materials with a ashpoint lower than

55°C.

Note : A mixing bucket (12) is provided to use when transfer-

ring spray material from the original container into the bucket

for thinning and measuring purposes (g. K).

Note : A viscosity cup (13) is provided to determine the

“runout time” of the material being used.

u Before measuring for the proper viscosity, stir the material

thoroughly.

u Dip the viscosity cup (13) into the material being sprayed

and ll the viscosity cup (13) completely.

u With the viscosity cup (13) held over the material con-

tainer, measure the amount of time it takes for the stream

of material owing out to “break” or stop being a constant

stream out of the bottom of the viscosity cup (13) (2

minutes or less) (g. L). This is the “runout time” Refer to

the thinning table for information on the thinning required

for different materials.

u If material needs thinning, add the appropriate liquid thin-

ning material recommended by the manufacturer.

u It is possible to spray latex paint with this unit, however,

the required thinning may exceed material manufacturer's

recommendation. Thin latex paint so that it runs through

viscosity cup (13) in under 2 minutes. The operator should

consider the type of application and nal location of the

project when spraying a material that requires more than 2

minutes to run through the viscosity cup (13).

Thinning table

Spray material Runout time

Clear and semi-transparent stains

and sealers

No thinning required

Oil based primers, varnishes and

polyurethane

(Less than 2 minute runout)

Solid colour water based stains May require thinning

Water based or latex paints (More than 2 minute runout)

Note : Not recommended for textured paint

Hints for optimum use

Preparation tips

u Always stir and strain the material thoroughly before use.

u With any spraying job you should always ensure that

you have properly prepared the surface to get the best

nish. That is, all surfaces are free from dust, dirt, rust and

grease. Lightly pressure wash decks or exterior surfaces

and ensure that they are dry before spraying.

u Even though HVLP sprayers have very little overspray,

it is recommended that you mask all edges and other

areas and use drop cloths to protect your oors and

anything else in the spraying area that you wish to remain

untouched.

u Skin that forms on the top of paint can clog the sprayer.

Remove skin before mixing. Strain with a funnel with a

lter attached or through hosiery to remove any impurities

that could clog system.

u Before starting have gloves, paper towels, rags etc. avail-

able for unexpected spills.

Developing the proper spraying technique (g. M & N)

u Practice spraying on a piece of scrap material such as

cardboard to test your spray pattern and become familiar

with the ow control feature of the sprayer.

u Ensure surface to be sprayed is free of dust, dirt, and

grease.

u Ensure spray area is clean and free of dust that could be

blown onto newly sprayed surfaces.

u Cover any areas not intended to be sprayed.

u Always spray from a minimum of 25mm to a maximum of

355mm (g. M).

u A commonly used method for spraying a large surface

is the “crisscross” pattern. This is done by spraying in

horizontal strips and then crossing over these strips with

vertical strips.

u To get an even spray distribution, always keep your arm at

the same distance (g. M) from the surface you are spray-

ing and avoid moving your wrist (g. N).

u Maintain smooth and consistent speed which will help

avoid inconsistencies. Begin spraying after the pass has

begun and release trigger before stopping the pass.

u Avoid spraying too heavily in any one area. Several lighter

coats are better than one heavy coat which can lead to

running and dripping. Remember that the ow control

knob regulates the amount of liquid that can be sprayed.

Turning the ow knob clockwise increases the ow of

liquid. Turning the knob counterclockwise decreases the

ow of liquid. If runs or drips do occur, have a dry paint

brush on hand to smooth them out.

u Turn the power unit off and place the sprayer in the built-in

dock of the power unit when not spraying for any length of

time.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Black Decker HVLP400 T1 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Black Decker HVLP400 T1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info