Bedienungsanleitung Blaupunkt viking tmc 148 (Seite 17 von 33) (Englisch)

165764

Zoom out

Zoom in

Vorherige Seite

1/33

Nächste Seite

ENGLISH

DEUTSCH

FRANÇAIS

ITALIANO

NEDERLANDS

SVENSKA

ESPAÑOL

PORTUGUÊS

Continue listening to a scanned

station/end Preset Scan:

• Press SC briefly.

Scanning stations with

Radio Scan

You can scan through all of the stations in

your reception area.

To start the Scan function:

• Press SC briefly.

The scanned frequency or the station name

will start flashing in the display.

During the scanning process “SCAN” will

appear in the display.

To select a scanned station/switch off

the Scan function:

• Press SC or the rocker switch briefly.

If no station is selected, the scan function

will switch off after the frequency band has

run through. The station selected previous-

ly will resume play.

Changing the Scan Time

The scan time can be selected from between

5 to a maximum of 30 seconds.

If you would like to alter the scan time, plea-

se refer to the section on “DSC programming

- SCANTIME”.

Automatic bandwidth adjust-

ment (FM)

In the DSC menu, you can use the SHARX

function to adjust the bandwidth in the FM

frequency range. This can be a great ad-

vantage when there are a large number of

stations within your current reception range.

Interference with strong adjacent stations

can be reduced to an absolute minimum if

you activate SHARX ON.

If necessary, refer to the section on “DSC

programming – SHARX”.

PTY - Programme Type

PTY is an RDS service which an increasing

number of more broadcasting stations have

begun to offer. This feature allows you to

select FM stations according to their pro-

gramme type. After you have chosen the

PTY of your preference, the corresponding

stations can be selected either by seek tu-

ning or using the scan function.

Switching PTY on/off

• Press PTY.

When the function is active, the programme

type selected last will appear briefly in the

display and as long as PTY is active, “PTY”

will appear permanently in the display.

Selecting the automatic tuning

sensitivity

You can alter the automatic tuning sensiti-

vity.

If “lo” is displayed, the radio will only pick up

strong, local stations (low sensitivity).

If “lo” does not light up, the radio will also

pick up weaker, more distant stations.

If you would like to alter the sensitivity level

please refer to the section on “DSC pro-

gramming – LO-DX”.

Switching from stereo to mono

(FM)

In the DSC menu, you might get better

sound quality by switching from stereo to

mono. This can be useful in areas where

reception is poor. Each time the radio is

switched on, stereo playback is activated

automatically.

The unit will automatically switch to mono if

the signal received is not strong enough for

stereo playback.

If you would like to switch to mono, refer to

“DSC programming - STEREO/MONO”.

The mode selected is indicated in the dis-

play.

Radio operation with RDS (Radio Data System)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Blaupunkt viking tmc 148 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Blaupunkt viking tmc 148

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info