Bedienungsanleitung Bosch AdvancedGrind 18 SystemBox (Seite 19 von 323) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

766843

Zoom out

Zoom in

Vorherige Seite

1/323

Nächste Seite

English | 19

plete stop. Never attempt to remove the cut-off wheel

from the cut while the wheel is in motion otherwise

kickback may occur. Investigate and take corrective ac-

tion to eliminate the cause of wheel binding.

uDo not restart the cutting operation in the workpiece.

Let the wheel reach full speed and carefully re-enter

the cut. The wheel may bind, walk up or kickback if the

power tool is restarted in the workpiece.

uSupport panels or any oversized workpiece to minim-

ize the risk of wheel pinching and kickback. Large

workpieces tend to sag under their own weight. Supports

must be placed under the workpiece near the line of cut

and near the edge of the workpiece on both sides of the

wheel.

uUse extra caution when making a “pocket cut” into ex-

isting walls or other blind areas. The protruding wheel

may cut gas or water pipes, electrical wiring or objects

that can cause kickback.

Safety Warnings specific for Sanding operations

uDo not use excessively oversized sanding disc paper.

Follow manufacturers recommendations, when select-

ing sanding paper. Larger sanding paper extending bey-

ond the sanding pad presents a laceration hazard and

may cause snagging, tearing of the disc, or kickback.

Safety Warnings specific for Wire Brushing operations

uBe aware that wire bristles are thrown by the brush

even during ordinary operation. Do not overstress the

wires by applying excessive load to the brush The wire

bristles can easily penetrate light clothing and/or skin.

uIf the use of a guard is recommended for wire brush-

ing, do not allow any interference of the wire wheel or

brush with the guard. Wire wheel or brush may expand

in diameter due to work load and centrifugal forces.

Additional safety information

Wear safety goggles.

uUse suitable detectors to determine if there are hid-

den supply lines or contact the local utility company

for assistance. Contact with electric cables can cause

fire and electric shock. Damaging gas lines can lead to ex-

plosion. Breaking water pipes causes property damage.

uDo not touch grinding and cutting discs until they have

cooled down. The discs can become very hot while work-

ing.

uRelease the On/Off switch and set it to the Off posi-

tion when the power supply is interrupted, e.g. when

the battery pack is removed. This prevents uncontrolled

restarting.

uSecure the workpiece. A workpiece clamped with

clamping devices or in a vice is held more secure than by

hand.

uIn case of damage and improper use of the battery, va-

pours may be emitted. The battery can set alight or ex-

plode. Ensure the area is well ventilated and seek medical

attention should you experience any adverse effects. The

vapours may irritate the respiratory system.

uDo not open the battery. There is a risk of short-circuit-

ing.

uThe battery can be damaged by pointed objects such

as nails or screwdrivers or by force applied externally.

An internal short circuit may occur, causing the battery to

burn, smoke, explode or overheat.

uOnly use the battery with products from the manufac-

turer. This is the only way in which you can protect the

battery against dangerous overload.

Protect the battery against heat, e.g. against

continuous intense sunlight, fire, dirt, water

and moisture. There is a risk of explosion and

short-circuiting.

Product Description and

Specifications

Read all the safety and general instructions.

Failure to observe the safety and general in-

structions may result in electric shock, fire

and/or serious injury.

Please observe the illustrations at the beginning of this oper-

ating manual.

Intended use

The power tool is intended for cutting, grinding, roughing

and brushing metal materials without the use of water.

A separate protective guard for cutting must be used when

cutting with bonded abrasives.

Sufficient dust extraction must be provided when cutting

stone.

With approved abrasive tools, the power tool can be used for

sanding with sanding discs.

Product Features

The numbering of the product features refers to the diagram

of the power tool on the graphics page.

(1) Unlocking lever for protective guard

(2) Spindle lock button

(3) Direction of rotation arrow on housing

(4) On/off switch

(5) Battery charge indicator

(6) Batterya)

(7) Speed preselection thumbwheel

(8) Battery release buttona)

(9) Auxiliary handle (insulated gripping surface)

(10) Protective guard for grinding

(11) Mounting flange with O‑ring

(12) Grinding disc

(13) Protective guard for cuttinga)

Bosch Power Tools 1 609 92A 6D6 | (25.06.2021)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch AdvancedGrind 18 SystemBox Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info