Bedienungsanleitung Bosch AdvancedGrind 18 SystemBox (Seite 21 von 323) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

766843

Zoom out

Zoom in

Vorherige Seite

1/323

Nächste Seite

English | 21

Removing the battery

To remove the battery (6), press the battery unlocking but-

ton (8) and pull the battery out of the power tool. Do not ex-

ert any force.

Charge-control Indicator

The charge-control indicator (5) displays the charge condi-

tion of the battery for several seconds when the On/Off

switch (4) is half-pressed or fully pressed. It consists of 3

green LEDs.

LED Capacity

Continuous lighting 3x green ≥ 66%

Continuous lighting 2x green 33–66%

Continuous lighting 1x green 11–33%

Slowly flashing light 1 x green ≤ 10%

The 3 LEDs in the charge-control indicator flash quickly

when the temperature of the battery is outside of the op-

erating temperature range of –30 to +65 °C and/or the

overload protection has been triggered.

Fitting Protective Equipment

uRemove the battery from the power tool before carry-

ing out work on the power tool (e.g. maintenance,

changing tool, etc.). The battery should also be re-

moved for transport and storage. There is risk of injury

from unintentionally pressing the on/off switch.

Note: If the grinding disc breaks during operation or the

holding fixtures on the protective guard/power tool become

damaged, the power tool must be sent to the after-sales ser-

vice immediately; see the "After-Sales Service and Applica-

tion Service" section for addresses.

Protective guard for grinding

Place the protective guard

(10) onto the holder on the

power tool until the coding

cams of the protective guard

are aligned with the holder.

When doing so, press and

hold the unlocking lever (1).

Press the protective guard

(10) onto the spindle collar

until the shoulder of the pro-

tective guard is sitting on the

flange of the power tool and

rotate the protective guard

until it audibly clicks into

place.

Adjust the position of the protective guard (10) to meet the

requirements of the operation. To do this, push the unlock-

ing lever (1) upward and rotate the protective guard (10)

into the required position.

uAlways position the protective guard(10) such that

the two cams on the unlocking lever(1) engage in the

corresponding openings on the protective guard(10).

uAdjust the protective guard (10) such that sparking in

the direction of the operator is prevented.

uThe protective guard (10) must only be adjustable

while the unlocking lever (1) is actuated. Otherwise,

the power tool must not be used any more under any

circumstances and must be sent to the after-sales ser-

vice.

Note: The coding cams on the protective guard (10) ensure

that only a protective guard that is suitable for the power

tool can be fitted.

Protective guard for cutting

uAlways use the protective guard for cutting (13) when

cutting with bonded abrasives.

uProvide sufficient dust extraction when cutting stone.

The protective guard for cutting (13) is fitted in the same

way as the protective guard for grinding (10).

Extraction guard for cutting with a guide block

The extraction guard for cutting with a guide block (24) is fit-

ted in the same way as the protective guard for grinding

(10).

Side handle

uDo not operate your power tool without the side

handle (9).

Screw the side handle (9) on the left or right of the machine

head depending on how your are working.

Low-vibration auxiliary handle

Screw the auxiliary handle

(9) on the left or right of the

machine head depending

on how your are working.

The low-vibration auxiliary handle reduces vibration, en-

abling the tool to be used safely and more comfortably.

uDo not make any alterations of any kind to the auxili-

ary handle.

Do not continue to use a damaged auxiliary handle.

Hand guard

uAlways fit the hand guard (18) when working with the

rubber sanding plate (19) or with the cup brush/disc

brush/flap disc.

Attach the hand guard (18) to the side handle (9).

Fitting the Abrasive Tools

uRemove the battery from the power tool before carry-

ing out work on the power tool (e.g. maintenance,

changing tool, etc.). The battery should also be re-

Bosch Power Tools 1 609 92A 6D6 | (25.06.2021)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch AdvancedGrind 18 SystemBox Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info