Bedienungsanleitung Bosch AdvancedGrind 18 SystemBox (Seite 22 von 323) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch)

766843

Zoom out

Zoom in

Vorherige Seite

1/323

Nächste Seite

22 | English

moved for transport and storage. There is risk of injury

from unintentionally pressing the on/off switch.

uDo not touch grinding and cutting discs until they have

cooled down. The discs can become very hot while work-

ing.

Clean the grinding spindle (17) and all the parts to be fitted.

Lock the grinding spindle with the spindle lock button (2)

before clamping and releasing the abrasive tools.

uDo not press the spindle lock button while the grind-

ing spindle is moving. The power tool may become dam-

aged if you do this.

Grinding/Cutting Disc

Pay attention to the dimensions of the abrasive tools. The

diameter of the hole must match that of the mounting flange.

Do not use an adapter or reducer.

When using diamond cutting discs, make sure that the direc-

tion of rotation arrow on the diamond cutting disc corres-

ponds to the direction of rotation of the machine (see direc-

tion of rotation arrow on the housing).

See the graphics page for fitting instructions.

Use the quick-clamping nut (16) to secure the grinding/cut-

ting disc without the need for additional tools.

uThe quick-clamping nut (16) may be used only for

grinding or cutting discs.

uOnly use quick-clamping nuts (16) that are in good

working order and not damaged.

uWhen screwing on, make sure that the printed side of

the quick-clamping nut (16) is not facing the grinding

disc.

uAlways secure a grinding/cutting disc using only the

quick-clamping nut (16) supplied.

Press the spindle lock but-

ton (2) to lock the grinding

spindle. To tighten the

quick-clamping nut (16),

fold up the bar and turn the

quick-clamping nut firmly

clockwise. Then fold down

the bar to secure the quick-

clamping nut. It is not suf-

ficient to tighten the disc

along the edge.

Quick-clamping nuts (16)

that are properly secured

and not damaged can be re-

moved by hand. To do this,

fold up the bar and turn the

quick-clamping nut firmly

anticlockwise. If the quick-

clamping nut is stuck, do

not attempt to loosen it with

a tool – always use a two-

pin spanner.

After fitting the hub flange

and the grinding/cutting

disc, the free thread length

of the grinding spindle must

be at least 4mm.

Ensure that the abrasive

tool is firmly seated, so that

it does not twist away from

the spindle in the runout of the power tool.

A plastic part (O-ring) is fitted around the cent-

ring collar in the hub flange (11). If the O-ring

is missing or damaged, the hub flange (11)

must be replaced before operation can re-

sume.

uAfter fitting the abrasive tool, check that the abrasive

tool is fitted correctly and can turn freely before

switching on the power tool. Make sure that the abras-

ive tool does not brush against the protective guard or

other parts.

Flap disc

uAlways fit the hand guard (18) when working with the

flap disc.

Rubber Sanding Pad

uAlways fit the hand guard (18) when working with the

rubber sanding pad (19).

See the graphics page for fitting instructions.

Slide the rubber sanding pad (19) onto the grinding spindle

(17).

Press the sanding sheet (20) firmly onto the underside of

the rubber sanding pad (19).

Screw on the round nut (21) and tighten with a two-pin

spanner.

Cup brush/disc brush

uAlways fit the hand guard (18) when working with the

cup brush or disc brush.

See the graphics page for fitting instructions.

The cup brush/disc brush must be screwed onto the grinding

spindle until it rests firmly against the grinding spindle flange

at the end of the grinding spindle thread. Tighten the cup

brush/disc brush with an open-ended spanner.

1 609 92A 6D6 | (25.06.2021) Bosch Power Tools

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch AdvancedGrind 18 SystemBox Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info