Bedienungsanleitung Bosch AdvancedImpact 900 (Seite 18 von 107) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

707745

Zoom out

Zoom in

Vorherige Seite

1/107

Nächste Seite

18 | English

Unlock the setting ring(17) by turning it to the left .

Place the dust container(11) or the adapter(26) flush

against the wall or workpiece. Move the tip of the drill bit to

the wall or workpiece.

Slide the setting ring(17) backwards until the distance

matches the required drilling depthX or place a wall plug on

the rail and slide the setting ring(17) backwards to the wall

plug. Lock the setting ring(17) by turning it to the right .

Take the wall plug out of the rail again. The drilling depth now

matches the set length X on the rail.

Note: It is important to have the exact drilling depth when

using wall plugs. If the drilled hole is too deep, the wall plug

will slip too far into the wall or workpiece. If the hole is too

small, the wall plug will stick out.

Emptying the dust container (see figure G)

The dust container(11) is enough for drilling about 25 holes

in masonry at a drilling depth of 30 mm with a drill bit dia-

meter of 6 mm.

To remove the dust container(11), press the side-mounted

unlocking buttons(12) and pull the dust container off down-

wards.

Empty the dust container(11) and reinsert it (until it can be

heard to engage).

Removing the Drill Assistant

Press and hold the clip(16) of the dust collection

device(13) and pull the dust collection device(13) off to-

wards the front.

Turn the wing bolt(18) anticlockwise until the auxiliary

handle(9) can be moved and pull the auxiliary handle(9) off

the power tool.

Unlock the setting ring(17) by turning it to the left .

Hold the auxiliary handle(9) in place and slide the rail to-

wards the auxiliary handle until it can be heard to engage.

Dust Extraction/Dust Container

The dust from materials such as lead paint, some types of

wood, minerals and metal can be harmful to human health.

Touching or breathing in this dust can trigger allergic reac-

tions and/or cause respiratory illnesses in the user or in

people in the near vicinity.

Certain dusts, such as oak or beech dust, are classified as

carcinogenic, especially in conjunction with wood treatment

additives (chromate, wood preservative). Materials contain-

ing asbestos may only be machined by specialists.

– Use a dust extraction system that is suitable for the ma-

terial wherever possible.

– Provide good ventilation at the workplace.

– It is advisable to wear a P2 filter class breathing mask.

The regulations on the material being machined that apply in

the country of use must be observed.

u Avoid dust accumulation at the workplace. Dust can

easily ignite.

u Use the dust box only when working on concrete and

stone. Wood chips and plastic chips can easily lead to

clogging.

u Warning: Danger of fire! Do not work on any metallic

materials with the dust container mounted. Hot metal

chips can ignite parts of the dust container.

Please observe the following instructions to optimise your

use of the dust container:

– Ensure that the dust container is placed flush against the

workpiece or wall. This also makes it easier to drill at a

right angle.

– When you reach the required drilling depth, pull the drill

bit out of the drill hole first and then switch off the impact

drill.

– The dust protection ring(15) can wear, especially when

working with large drill-bit diameters. Replace the dust

protection ring when worn/damaged.

Changing the Tool

Keyless chuck (see figure H)

The drill spindle is locked when the on/off switch (6) is not

pressed. This makes it possible to change the application

tool in the drill chuck quickly, conveniently and easily.

Open the keyless chuck (1) by turning it in the direction of

rotation  until the tool can be inserted. Insert the tool.

Firmly tighten the sleeve of the keyless chuck (1) by turning

it by hand in the rotational direction  until it stops clicking.

This will automatically lock the drill chuck.

The lock will disengage again if you turn the sleeve in the op-

posite direction to remove the tool.

Screwdriving tools

You should always use a universal bit holder (24) when using

screwdriver bits (25). Only use screwdriver bits that fit the

screw head.

For screwdriving, make sure the "drilling/impact drilling" se-

lector switch (2) is always set to the "drilling" symbol.

Changing the drill chuck

u Pull the plug out of the socket before carrying out any

work on the power tool.

1 609 92A 57F | (27.08.2019) Bosch Power Tools

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch AdvancedImpact 900 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info