Bedienungsanleitung Bosch AdvancedImpact 900 (Seite 19 von 107) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

707745

Zoom out

Zoom in

Vorherige Seite

1/107

Nächste Seite

English | 19

Removing the drill chuck (see figure I)

Remove the auxiliary handle (9) and set the gear selector

switch (3) to the middle position between first and second

gear.

Insert a steel pin with a diameter of 4 mm and a length of ap-

prox. 50 mm into the hole on the spindle collar to lock the

drill spindle in place. Clamp a hex key (27) in the keyless

chuck (1), leading with the short shaft.

Place the power tool on a firm surface, e.g. a work bench.

Hold the power tool in place and loosen the keyless chuck

(1) by turning the hex key (27) in the rotational direction .

A tightly seated keyless chuck is loosened with a light blow

on the long shaft of the hex key (27). Remove the hex key

from the keyless chuck and completely unscrew the keyless

chuck from the power tool.

Fitting the Drill Chuck (see figure J)

To assemble the keyless chuck, perform the same steps in

reverse order.

The drill chuck must be tightened using a tight-

ening torque of approx. 50–55 Nm.

u After successfully fitting the drill chuck, remove the

steel pin from the hole again.

Operation

Starting Operation

u Pay attention to the mains voltage. The voltage of the

power source must match the voltage specified on the

rating plate of the power tool. Power tools marked

with 230V can also be operated with 220V.

u Products that are only sold in AUS and NZ: Use a resid-

ual current device (RCD) with a nominal residual current

of 30 mA or less.

Setting the Rotational Direction (seefigureK)

The rotational direction switch (4) is used to change the ro-

tational direction of the power tool. However, this is not pos-

sible while the on/off switch (6) is being pressed.

Right rotation: To drill and to drive in screws, press the ro-

tational direction switch (4) through to the right stop.

Left rotation: To loosen and unscrew screws and nuts,

press the rotational direction switch (4) through to the left

stop.

Setting the Operating Mode

Drilling and screwdriving

Set the selector switch (2) to the "drilling"

symbol.

Impact drilling

Set the selector switch (2) to the "impact

drilling" symbol.

The selector switch (2) clicks into place and can also be ac-

tuated when the motor is running.

Mechanical gear selection

u You can press the gear selector switch (3) with the

power tool running at a low speed. You should not do

this at full load or maximum torque, or when the tool is

not in use, however.

You can preselect two speed ranges with the gear selector

(3).

Gear I:

Low speed range; for working with a large

drilling diameter or for screwdriving.

Gear II:

High speed range; for working with a small

drilling diameter.

Always turn the gear selector switch(3) in the

direction of the arrow.

If the gear selector (3) cannot be swivelled all the way to the

stop, turn the drive spindle slightly with the drill.

Switching on/off

To start the power tool, press and hold the on/off switch

(6).

Press the lock-on button (5) to lock the on/off switch (6) in

this position.

To switch off the power tool, release the on/off switch (6);

or, if the switch is locked with the lock-on button (5), briefly

press the on/off switch (6) and then release it.

Emergency switch-off (KickBack Control)

The emergency switch-off function (Kick-

Back Control) gives the user greater control

over the power tool and offers them better

protection than power tools that do not

have KickBack Control. The power tool will switch off if it

suddenly and unforeseeably rotates around the drilling

axis.

To switch the tool back on, release the on/off switch and

then press it again.

u If the KickBack Control function is defective, it will no

longer be possible to switch the power tool on. Have

the power tool serviced by a qualified repair person

using only original replacement parts.

Adjusting the Speed/Impact Rate

You can adjust the speed/impact rate of the power tool when

it is on by pressing in the on/off switch (6) to varying ex-

tents.

Applying light pressure to the on/off switch (6) results in a

low rotational speed/impact rate. Applying increasing pres-

sure to the switch increases the speed/impact rate.

Preselecting the speed/impact rate

You can preselect the required speed/impact rate using the

speed preselection thumbwheel (7), even during operation.

The required speed/impact rate is dependent on the mater-

ial and the work conditions and can be determined by prac-

tical trials.

Bosch Power Tools 1 609 92A 57F | (27.08.2019)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch AdvancedImpact 900 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info