Bedienungsanleitung Bosch AMAX panel 4000 EN (Seite 38 von 170) (Englisch)

697454

Zoom out

Zoom in

Vorherige Seite

1/170

Nächste Seite

38 en | Settings AMAX panel

2019.08 | 11 | F.01U.309.277 Installation Manual Bosch Security Systems B.V.

6.1.2 Reports

System reporting

Report transmission sequence

If the event has disabled the report (option 0), no report is sent out. If the report has any

destination to contact the panel (option 1 - 11), It will call the related destination by related

reporting format type and subscriber ID number.

Attempt rules:

1. Attempt times and duration

– Within the report expiring time the AMAX panel will retry sending the report to each

enabled destination till the report has been sent to the destination, or till the report

buffer overflows and the old report is replaced by new incoming reports.

– For each enabled destination, the retry interval time between two retries is 15

seconds for the 1st retry to 4th retry, and the retry interval time between two retries

is 10 minutes for the 5th retry to 8th retry, after the 8th retry the retry interval time

between two retries is 60 minutes.

2. Attempt priority

– The attempt priority is destination 1, 2, 3, 4 Domestic. The disabled destinations will

be ignored.

3. Communication fail fault

– If the attempt times for one destination reaches 4, the system will cause the

communication fail fault for this destination.

4. Backup destination process

– The AMAX panel can save up to a maximum of 50 un-reported events. If the un-

reported events are more than 50, it will delete earlier event and only save the last

50 events in the buffer to send out.

Sequential logic to send report

– If the event reporting path is disabled, the relevant reports will not be sent.

– If the event reporting path is set to a single path (receiver 1, 2, 3 or 4), the AMAX panel

will send a report to the corresponding path.

– If the event reporting path is set to more than one path (e.g. receiver 1, 2, 3, 4) and any

of these paths fails, the reporting will fail.

– If the event reporting path is set to one or more receivers with other receivers as backup,

the AMAX panel will send the report to the main receivers first. Only this reporting fails,

the AMAX panel attempts to send the report to the backup receivers in succession.

Communication path fault will occur when all valid paths fail. Communication path fault

will recover when any one of the paths recovers.

Display of faults

When multiple reports are queued for delivery, the communication path fault is displayed as a

logic or relationship. Example:

Set zone status recovery report to send report to receiver 1. Set keypad emergency report to

send report to receiver 1, with receiver 2, 3, and 4 as backup.

Communication path fault is as follows: When communication paths 1, 2, 3, and 4 all fail, only

the illumination of zone indicator 1 expresses that communication path 1 of the zone status

recovery report fails and the all communication paths 1, 2, 3 and 4 of the keypad emergency

report fail as well.

Communication path fault recovery is as follows:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch AMAX panel 4000 EN Seite 38

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bosch AMAX panel 4000 EN

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info