Bedienungsanleitung Bosch AMAX panel 4000 EN (Seite 39 von 170) (Englisch)

697454

Zoom out

Zoom in

Vorherige Seite

1/170

Nächste Seite

AMAX panel Settings | en 39

Bosch Security Systems B.V. Installation Manual 2019.08 | 11 | F.01U.309.277

– When communication path 1 fault recovers, zone indicator 1 goes off, indicating that the

communication path 1 fault of the zone status recovery report recovers and the

communication part 1 fault of the keypad emergency report recovers

– When any one path fault of communication paths 2, 3, and 4 recover, as the

communication path fault is displayed as a logic or relationship, zone indicator 1 still

illuminates, indicating that the communication path 1 fault of the zone status recovery

report has not be recovered, but the path fault of the keypad emergency report has been

recovered

Zone status reporting and zone recovery reporting

Zone restore report

Alarm report

In arming status, in case of alarm event, the alarm report will be sent.

Alarm recovery report

In arming status, when a zone is restored, a zone recovery report is sent either if the lock-out

option for the zone is disabled or if the lock-out option for the zone is enabled and the alarm

output time has ended.

If the non-24-hour zone is not recovered in disarming, the system will automatically send a

zone recovery report. The 24-hour zone sends the recovery report only when the zone

recovers.

Zone fault report

If the zone is triggered at the end of exit delay, a zone fault report will be sent, indicating that

the zone is automatically bypassed by the system. At the end of exit delay time, the 24-hour

zone in triggering status will not send the fault report, i.e. the 24-hour zone will not be

automatically bypassed.

The non 24-hour zone fault recovery report will be sent when the zone recovers or the system

disarms. For the 24-hour zone, only the alarm recovery event will occur.

The zone fault occurs when the zone is triggered and recovers when the zone is normal. Zone

fault will occur when one of the following conditions is met:

– For 24-hour zone, (internal) instant zone, if the forced arming option is set to allow, the

zone fault event will occur when the arming operation is executed while the zone is in

triggering status

– When the zone is locked

– For (internal) delay and (internal) follow zone, if they are still in triggering status at the

end of exit delay, zone fault event will occur

– For 24-hour zone, if it is in triggering status when the bypass is cancelled, zone fault

event will occur

Fault recovery conditions:

– Zone resumes to normal conditions

– When the failed (internal) delay zone, (internal) instant zone and (internal) follow zone

are disarmed, the fault recovery event will occur even if the zone is still in triggering

status

Zone bypass report

After a manual zone bypass operation is executed, the zone is bypassed and a relevant zone

bypass report is sent.

The zone bypass will be recovered when the system is disarmed and the zone bypass recovery

report will also be sent while disarming.

Zone tamper alarm

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch AMAX panel 4000 EN Seite 39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bosch AMAX panel 4000 EN

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info