Bedienungsanleitung Bosch Drive Unit Cruise (Seite 23 von 141) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Schwedisch, Norwegisch)

657566

Zoom out

Zoom in

Vorherige Seite

1/141

Nächste Seite

English–2

Bosch eBike Systems 0 276 001 YYY | (12.10.12)

Technical Data

Assembly

Inserting and Removing the Battery Pack

For inserting and removing the battery pack in/from the

eBike, please read and observe the battery pack operating in-

structions.

Inserting and Removing the Drive HMI

(see figure A)

To insert the drive HMI 3, slide it from the front into the

holder 4.

To remove the drive HMI 3, press the lock latch 15 and slide

the drive HMI toward the front out of the holder 4.

 Remove the drive HMI when parking the eBike, so that

the drive cannot be used by unauthorised persons.

Without the drive HMI, the eBike system cannot be

switched on.

The drive HMI can also be secured in

the holder against re-

moving. For this, remove the holder 4 from the handlebar. In-

sert the drive HMI into the holder. Screw the locking screw 16

from below into the corresponding thread in the holder.

Mount the holder onto the handlebar again.

Checking the Speed Sensor (see figure B)

The speed sensor 17 and its spoke magnet 18 must be

mounted in such a manner that the spoke magnet, after a turn

of the wheel, moves past the speed sensor with a clearance of

at least 5 mm, yet no more than 17 mm.

Note: If the clearance between speed sensor 17 and spoke

magnet 18 is too small or too large, or if the speed sensor 17

is not properly connected, the speed indication e w

ill fail, and

the eBike drive will operate in emergency mode.

In this case, loosen the screw of the spoke magnet 18 and fas-

ten the spoke magnet to the spoke in such a manner that it

runs past the mark of the speed sensor at the correct clear-

ance. When the speed is still not being indicated in the speed

indication e after this, please refer to an authorised bicycle

dealer.

Operation

Initial Operation

Requirements

The eBike system can only be activated when the following re-

quirements are met:

–A sufficiently charged battery pack is inserted (see operat-

ing instructions of the battery pack).

–The drive HMI is properly inserted in the holder (see “In-

serting and Removing the Drive HMI”, page English–2).

–The drive HMI is properly connected (see “Checking the

Speed Sensor”, page E

nglish–2).

Switching the eBike System On/Off

Options for switching on the eBike system:

–If the drive HMI is already switched on when inserting it in

the holder, the eBike system is automatically switched on.

–When the drive HMI and the battery pack are inserted,

briefly press the On/Off button 5 of the drive HMI once.

–When the drive HMI is in

serted, press the On/Off button of

the battery pack (see battery pack operating instructions).

Note: When switching on the eBike system, the pedals of the

eBike must not be subject to load, as otherwise the motor out-

put capacity will be limited. The error message “Release ped-

al” is displayed in text indication c.

If the eBike system was inadvertently switched on with load

applied to the pedals, th

en switch it off and then on again

without load.

The drive is activated as soon as you step into the pedals (ex-

cept when in push-assistance mode, see “Switching the Push-

assistance mode On/Off”, page English–4). The motor out-

put depends on the settings of the drive HMI.

Drive Unit Drive Unit Cruise

Article number

0 275 007 006/

0 275 007 007

Power output

W250

Output torque, max.

Nm50

Rated voltage

V 36

Operating temperature

°C –5...+40

Storage temperature

°C –10...+50

Degree of protection

IP 54 (dust and splash

water protected)

Weight, approx.

kg 4

Drive HMI Intuvia

Article number

1 270 020 903

Max. charging current, USB

connection.

mA 500

Charging voltage, USB con-

nection

V 5

Operating temperature

°C –5...+40

Storage temperature

°C –10...+50

Degree of protection

IP 54 (dust and splash

water protected)

Weight, approx.

kg 0.15

Lighting*

Rated voltage V 6

Power output

–Front light

– Rear light

2.7

0.3

* Not possible via the eBike battery pack in all country-specific versions,

depending on the statutory regulations

OBJ_BUCH-1407-003.book Page 2 Friday, October 12, 2012 1:01 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch Drive Unit Cruise Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info