Bedienungsanleitung Bosch Drive Unit Cruise (Seite 24 von 141) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Schwedisch, Norwegisch)

657566

Zoom out

Zoom in

Vorherige Seite

1/141

Nächste Seite

English–3

0 276 001 YYY | (12.10.12) Bosch eBike Systems

As soon as you stop pedaling when in normal operation, or as

soon as you have reached a speed of 25 km/h, the assistance

from the eBike drive is switched off. The drive is automatically

re-activated as soon you start pedaling again and the speed is

below 25 km/h.

Options for switching off the eBike system:

–Press the On/Off button 5 of the drive HMI.

–Switch t

he battery pack off by its On/Off button (see bat-

tery pack operating instructions.)

– Remove the drive HMI out of its holder.

When no power output of the drive is requested for approx.

10 minutes (e. g., because the eBike is parked) and no button

of the drive HMI or operating unit is pressed, the battery pack

automatically switches off to save energy.

Indications and Settings of the Drive HMI

Power Supply of the Drive HMI

When the drive HMI is inserted in holder 4, a sufficiently

charged battery pack is inserted in the eBike and the eBike

system is switched on, power is supplied to the drive HMI via

the eBike's battery pack.

When the drive HMI is removed from holder 4, it is supplied

with power via an internal battery pack. If the internal battery

pack is lo

w when switching on the drive HMI, “Attach to bike”

is displayed for 3 s in text indication c. Afterwards, the drive

HMI switches off again.

To recharge the internal battery pack, insert the drive HMI in-

to the holder 4 (a battery pack must be inserted in the eBike).

Switch the eBike battery pack off by its On/Off button (see

battery pack operating instru

ctions).

The drive HMI can also be charged via USB connection. Open

protective cap 8 for this. Using a matching USB cable, con-

nect the USB port 7 of the drive HMI to a commercially availa-

ble USB charger or to the USB port of a computer; (5 V charg-

ing voltage; max. 500 mA charging current). “USB

connected” is displayed in text indication c of the drive HMI.

Switching the drive HMI On/Off

To switch on the driv

e HMI, briefly press the On/Off button 5.

When the internal battery pack is sufficiently charged, the

drive HMI can also be switched on when not inserted in the

holder.

To switch off the drive HMI, press the On/Off button 5.

When the drive HMI is not inserted in the

holder and no button

is pressed, it automatically switches off after 1 min to save en-

ergy.

Battery Charge-control Indicator

The battery-pack charge-control indicator f indicates the

charge condition of the eBike’s battery pack, and not the

charge condition of the drive HMI’s internal battery pack. The

charge condition of the eBike’s battery pack can also be read

from the battery pack’s LEDs.

On indicator f, each bar of the battery pack symbol is equiv

lent to a capacity of approx. 20 %:

Less than 5 % capacity; drive assistance is no long-

er possible. The LEDs of the charge-control indica-

tor on the battery pack go out.

When the eBike lighting is powered via the battery pack

(country-specific), the capacity upon first indication of the

empty battery pack symbol will be sufficient for approx.

2 hours of lighting. When the symbol begins to flash, the light-

ing w

ill continue to operate only for a short period.

When the drive HMI is removed from holder 4, the last indicat-

ed battery pack charge condition is stored.

Setting the Assistance Level

The level of assistance of the eBike drive when pedaling can

be adjusted via the drive HMI. The assistance level can be

changed anytime, even during riding.

Note: For individual

versions, it is possible that the the assis-

tance level is pre-set and cannot be changed. It is also possi-

ble that less assistance levels are available for selection than

listed here.

The following assistance levels (max.) are available:

–“OFF”: The drive is switched off, the eBike can be operated

as a normal bicycle through pedaling.

–“ECO”: Effective assistance at maximum efficiency for

maximum cruising range

–“

TOUR”: Uniform assistance, for touring with long cruising

range

–“SPORT”: Powerful assistance for sportive riding off road

as well as for urban traffic

–“TURBO”: Maximum assistance, supporting highest ca-

dence for sportive riding

To increase the assistance level, press the “+” button 13 on

the operating unit until the desired assistance le

vel is dis-

played in indicator b; to decrease the assistance level, press

the “ –” button 12.

The requested motor output is displayed in indicator a. The

maximum motor output depends on the selected assistance

level.

When the drive HMI is removed from holder 4, the last indicat-

ed assistance level is stored; the motor-output indicator a re-

mains empty.

100 % to 80 % capacity

20 % to 5 % capacity; the battery pack should be

recharged.

Assistance Level Motor Output*

Derailleur Gear Hub

“ECO”

30 % 30 %

“TOUR”

100 % 90 %

“SPORT”

170 % 150 %

“TURBO”

250 % 200 %

*The motor output can vary for individual versions.

OBJ_BUCH-1407-003.book Page 3 Friday, October 12, 2012 1:01 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch Drive Unit Cruise Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info