Bedienungsanleitung Bosch Drive Unit Cruise (Seite 25 von 141) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Schwedisch, Norwegisch)

657566

Zoom out

Zoom in

Vorherige Seite

1/141

Nächste Seite

English–4

Bosch eBike Systems 0 276 001 YYY | (12.10.12)

Switching the Push-assistance mode On/Off

The push-assistance feature makes it easier to push the

eBike. The speed in this function depends on th e set gear an d

cannot exceed 6 km/h (max.). The lower the set gear, the low-

er the speed in the push-assistance function (at full output).

 The push-assistance function may only be used when

pushing the eBike. Danger of injury when the wheels of

the eBike do not hav

e ground contact while using the push-

assistance function.

To activate the push-assistance function, press and hold the

“WALK” button 14 on the operating unit. The eBike's drive is

activated.

The push-assistance function is switched off as soon as any

of the following incidents occ

ur:

–You release the “WALK” button 14,

–You pedal in forward or quickly in backward direction,

–The wheels of the eBike are blocked (e. g., through braking

or running against an obstruction),

–Your speed exceeds 6 km/h.

Switching the Lighting On/Off

Depending on country-specific regulations, two lighting ver-

sions are possible:

–The front light, rear light and display backlight can be

switched on and off at the same time via the drive HMI.

In this version, “Lights on” is displayed for approx. 1 s in

text indication c when switching on, and “Lights off” when

switching off.

– Only the display backlight can be switched on and off; the

front and rear light of the eBike are independent of th

drive HMI.

For both versions, the lighting is switched on and off by

pressing button 2.

Speed and Distance Indication

The speed indication e always displays the current speed.

The following functions are available in the function indica-

tion (combination of text indication c and value indication d):

–“Range”: Estimated range of the available battery-pack

charge (for constan

t conditions such as assistance level,

route profile, etc.)

–“Distance”: Distance covered since the last reset

–“Trip time”: Trip time since the last reset

–“Avg. Speed”: Average speed achieved since the last reset

–“Max. Speed”: Maximum speed achieved since the last re-

set

–“Clock”: Current time

To switch between the indication functions, press the “i”

button 1 on the drive HM

I or the “i” button 11 on the operating

unit until the desired function is displayed.

To reset “Distance”, “Trip time” and “Avg. Speed”, switch to

any of the three functions and then press and hold the

“RESET” button 6 until the indication is set to zero. This also

resets the values of the other two functions.

To reset the “Max. Speed”, switch to this function and then

press and hold the “RESET” button 6 until the indication is set

to zero.

When the drive HMI is removed from the holder 4, all function

values remain stored and can be viewed.

Displaying/Adapting Basic Settings

The basic settings can be displayed and changed no matter if

he drive HMI is in the holder 4 or not.

To access the basic settings menu, press and hold the

“RESET” button 6 and the “i” button 1 until “Configuration”

is displayed in text indication c.

To switch between the basic settings, press the “i” button 1

on the drive HMI until the desired basic setting is displayed.

When the drive HM

I is inserted in holder 4, you can also press

the “i” button 11 on the operating unit.

To change the basic settings, press the On/Off button 5 next

to the “ –” indication to decrease the value or scroll down, or

the illumination button 2 n ext to the “+” indication to increase

the value or scroll up.

hen the drive HMI is inserted in holder 4, you can also

change the values with the “ –” button 12 or the “+” button 13

on the operating unit.

To exit the function and store a changed setting, press the

“RESET” button 6 for 3 s.

The following basic settings are available:

–“unit km/mi”: Th e speed an d distance can be displayed ei-

ther in kilometres or miles.

–“time format”: The time can be displayed either in the

12 hour or 24 hour format.

–“clock”: The current time can be set here. Pressing and

holding the setting buttons fast-forwards the setting

speed.

–“English”: The language for text indication can be

chan

ged. The available languages are German, English,

French, Spanish, Italian and Dutch.

–“odometer”: Indicates the total distance travelled with the

eBike (not changeable).

–“power-on hours”: Indicates the total travel duration with

the eBike (not changeable).

Error Code Indication

The components of the eBike system are continu

ously and au-

tomatically monitored. When an error is detected, the respec-

tive error code is indicated in text indication c.

To return to the standard indication, press any button on the

drive HMI 3 or on the operating unit 10.

Depending on the type of error, the drive is automatically shut

off if required. Continued travel wit

hout assistance from the

drive is possible at any time. However, have the eBike

checked before attempting new trips.

 Have all inspections and repairs carried out only by an

authorised bicycle dealer. When an error is still displayed

despite corrective measures, please also refer to an

authorised bicycle dealer.

OBJ_BUCH-1407-003.book Page 4 Friday, October 12, 2012 1:01 PM

Bosch Drive Unit Cruise Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info