776836
14
Zoom out
Zoom in
Vorherige Seite
1/111
Nächste Seite
14 | English
Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Speed preselection thumbwheel
(2) Batterya)
(3) Battery release buttona)
(4) Sanding disc
(5) Battery charge indicator
(6) On/off switch
(7) Handle (insulated gripping surface)
(8) Sanding neta)
(9) Sanding disc holder
(10) Dust extraction adapter
(11) Vacuum hosea)
(12) Rubber band
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical Data
Cordless Disc Sander EasyCurvSander 12
Article number 3 603 JC9 0..
Rated voltage V 12
Speed preselection
Idle speed n0A) min-1 800–1800
Sanding pad diameter mm 38
Weight according to EPTA-
Procedure 01:2014A) kg 0.5
Recommended ambient
temperature during char-
ging
°C 0to+35
Permitted ambient temper-
ature during operationB) and
during storage
°C –20to+50
Recommended re-
chargeable batteries PBA12V…
Recommended chargers GAL 12...
A) Depends on battery in use
B) Limited performance at temperatures <0°C
Noise/Vibration Information
Noise emission values determined according
toEN62841-2-4.
Typically, the A-weighted sound pressure level of the power
tool is less than 70dB(A). The noise level when working can
exceed the volume stated. Wear hearing protection!
Total vibration values ah (triax vector sum) and uncertainty K
determined according to EN62841-2-4:
ah = 2.5 m/s2, K = 1.5 m/s2.
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Assembly
uRemove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Charging the Battery
uUse only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery of
your power tool.
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
uDo not continue to press the On/Off switch after the
power tool has automatically switched off. The battery
can be damaged.
Follow the instructions on correct disposal.
Removing the Battery (seefigureA)
To remove the battery(2), press the release buttons(3) and
pull the battery out of the power tool. Do not use force to
do this.
Battery charge indicator
The battery charge indicator(5) on the power tool consists
of three green LEDs. It indicates the battery's state of charge
for a few seconds after the power tool is switched on and off.
LED Capacity
Continuous lighting 3x green 60–100%
1 609 92A 66A | (26.01.2021) Bosch Power Tools
14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Bosch EasyCurveSander 12 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info