Bedienungsanleitung Bosch EasyCurveSander 12 (Seite 16 von 111) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch)

776836

Zoom out

Zoom in

Vorherige Seite

1/111

Nächste Seite

16 | English

When working on vertical surfaces, hold the power tool with

the dust extraction hose facing downwards.

Operation

Starting Operation

Inserting the Battery

Slide the charged battery(2) into the power tool until the

battery is securely locked.

Switching On/Off

uMake sure that you are able to press the On/Off switch

without releasing the handle.

To switch on the power tool, press the on/off switch(6).

To switch off the power tool, press the on/off switch(6)

again.

Preselecting the Speed

You can preselect the required speed using the speed

preselection thumbwheel(1), even during operation.

1 low speed

2 medium speed

3 high speed

The required speed depends on the material and the work-

ing conditions; it can be ascertained through practical tests.

After working at a low speed for an extended period, you

should operate the power tool at the maximum speed for ap-

prox. three minutes without load to cool it down.

Working Advice

uRemove the battery from the power tool before carry-

ing out work on the power tool (e.g. maintenance,

changing tool, etc.). The battery should also be re-

moved for transport and storage. There is risk of injury

from unintentionally pressing the on/off switch.

uAlways wait until the power tool has come to a com-

plete stop before placing it down.

uThis power tool is not suitable for bench-mounted use.

It must not be clamped into a vice or fastened to a work-

bench, for example.

Tip: Always sand curves at a low speed for best results.

Tip: The ergonomically shaped gripping surface allows for

dynamic and fatigue-free handling of the power tool (see fig-

ure F).

Sanding Surfaces

uWear protective gloves when grinding metals.

Switch the power tool on, place it against the surface of the

workpiece and apply moderate pressure as you move it over

the workpiece.

The material removal rate and sanding result are primarily

determined by the choice of sanding net, the preselected

speed setting and the contact pressure.

Only sanding nets in perfect condition achieve good sanding

performance and make the power tool last longer.

Be sure to apply consistent contact pressure in order to in-

crease the service life of the sanding nets.

Excessively increasing the contact pressure will not lead to

increased sanding performance; rather, it will cause more

severe wear of the power tool and of the sanding net.

Do not use sanding nets for other materials after they have

been used to work on metal.

Use only original Bosch-sanding accessories.

Rough Sanding

Attach sanding nets with a coarse grit.

Apply only light pressure to the power tool so that it runs at a

higher speed and a higher material removal rate is achieved.

Fine Sanding

Attach sanding nets with a fine grit.

You can reduce the sanding disc speed by varying the con-

tact pressure slightly or changing the speed setting, al-

though the random orbit motion is retained.

Applying moderate pressure, move the power tool over the

surface of the workpiece, either in a circular motion or al-

ternating between crossways and lengthways. To avoid

sanding through the workpiece, e.g. veneers, do not tilt the

power tool.

Switch the power tool off once you have finished your work.

Polishing

For polishing weathered paint or buffing out scratches (e.g.

in acrylic glass) and for polishing waxed/lubricated surfaces,

the power tool can be fitted with polishing sponges (ac-

cessories).

Select a low speed for polishing (level1) to prevent the sur-

face from overheating.

Apply the polish to an area slightly smaller than the area

which you intend to polish. Work the polishing agent in with

the polishing sponges, using side-to-side or circular motions

and applying moderate pressure.

Do not allow the polish to dry out on the surface; this may

damage the surface. Do not expose the surface which you in-

tend to polish to direct sunlight.

Clean the polishing sponges regularly to ensure good polish-

ing results. Wash out the polishing sponge with a mild deter-

gent and warm water; do not use paint thinner.

Application Table

The figures in the table below are recommended values.

The best method for determining the best combination while

sanding or polishing is practical experimentation.

Application Sanding net colour

(coarse/fine sanding) Speed setting

Abrading paint Yellow/green 2

Retouching paint Yellow 2/3

1 609 92A 66A | (26.01.2021) Bosch Power Tools

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch EasyCurveSander 12 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info