Bedienungsanleitung Bosch EasyCurveSander 12 (Seite 15 von 111) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch, Schwedisch, Norwegisch)

776836

Zoom out

Zoom in

Vorherige Seite

1/111

Nächste Seite

English | 15

LED Capacity

Continuous lighting 2x green 30–60%

Continuous lighting 1x green 10–30%

Slowly flashing light 1 x green 0–10%

The three LEDs in the battery charge indicator flash

quickly when the temperature of the battery is outside

the operating temperature range of -30 to +70 °C and/or

the overload protection has been triggered.

Selecting a sanding net

Select sanding nets with a grit suitable for how much material you want to remove. Bosch sanding nets are suitable for paint

and wood.

Use Application Grit Colour of

the stripe

on the

sanding

net

Remove

(coarse sand-

ing)

– Coarse sanding work with a

high material removal rate

– Removing old paint

– Sanding down old paint, varnish and filler

– Removing thin paint

– Pre-sanding rough, unplaned surfaces

Coarse/

P80 Orange

Prepare

(intermediate

sanding)

– Light sanding

– Abrading surfaces for further

processing later on

– Sanding uneven surfaces to make them

even

– Removing marks left by coarse sanding

– Repairing surfaces before applying paint or

varnish

Medium/

P180 Yellow

Finish – Intermediate paint sanding

– Abrading flaws in the paintwork

– Removing fibres from the surface

– Fine sanding before staining

– Abrading primer before painting

Very fine/

P320 Green

Changing the Sanding net (see figure B)

Note: Always sand with sanding nets attached.

To remove the sanding net(8), lift it from the side and pull it

from the sanding disc(4).

Remove dirt and dust from the sanding disc(4), e.g.with a

paintbrush or vacuum, before attaching a new sanding net.

The surface of the sanding disc(4) is fitted with a hook-and-

loop fastening, allowing sanding nets with a similar backing

to be secured quickly and easily.

Press the sanding net(8) firmly against the underside of the

sanding disc(4).

Note: Sanding nets must be positioned correctly in order to

ensure low vibration of the power tool during operation.

Changing the sanding disc (see figure C)

Note: Replace damaged sanding discs (4) immediately.

Remove the battery from the power tool.

Remove the sanding net or polishing sponge.

Pull the sanding disc (4) out of the sanding disc holder (9).

Position the new sanding disc(4). When doing so, ensure

that the large recesses on the sanding disc(4) engage in

the locking pins on the sanding disc holder(9). Then push

down firmly on the sanding disc(4) until it clicks into place.

Dust/Chip Extraction

The dust from materials such as lead paint, some types of

wood, minerals and metal can be harmful to human health.

Touching or breathing in this dust can trigger allergic reac-

tions and/or cause respiratory illnesses in the user or in

people in the near vicinity.

Certain dusts, such as oak or beech dust, are classified as

carcinogenic, especially in conjunction with wood treatment

additives (chromate, wood preservative). Materials contain-

ing asbestos may only be machined by specialists.

– Use a dust extraction system that is suitable for the ma-

terial wherever possible.

– Provide good ventilation at the workplace.

– It is advisable to wear a P2 filter class breathing mask.

The regulations on the material being machined that apply in

the country of use must be observed.

uAvoid dust accumulation at the workplace. Dust can

easily ignite.

External Dust Extraction (seefigureD–E)

Clip the dust extraction adapter (10) in over the sanding

disc holders (9). Then place the rubber band (12) of the

dust extraction adapter (10) over the power tool battery (2)

on the handle. Insert the vacuum hose (11) into the extrac-

tion adapter (10). Connect the vacuum hose (11) to a dust

extractor. You will find an overview of how to connect vari-

ous dust extractors at the end of these operating instruc-

tions.

The dust extractor must be suitable for the material being

worked.

When extracting dry dust that is especially detrimental to

health or carcinogenic, use a special dust extractor.

Bosch Power Tools 1 609 92A 66A | (26.01.2021)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch EasyCurveSander 12 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info