786104

Bosch GHO 12V-20 Professional Seite 15

15
Zoom out
Zoom in
Vorherige Seite
1/223
Nächste Seite
English | 15
Technical data
Planer GHO 12V-20
Article number 3 601 EA7 0..
Rated voltage V 12
No-load speed min-1 14,500
Cutting depth
– optimum mm 0 – 1.0
– maximum mm 1.0 – 2.0
Rebating depth mm 0 – 17
Max. planing width mm 56
Weight according to
EPTA-Procedure 01:2014 kg 1.7 – 1.9 A)
Permitted ambient temperature
– during charging °C 0 to +45
– During operation B) and dur-
ing storage °C -20 to +50
Recommended batteries GBA 12V...
GBA 10.8V...
Recommended chargers AL 11.. CV
GAL 1110 CV
GAL 12.. CV
GAL 12V-..
GAX 18V-30
A) Depends on battery in use
B) Limited performance at temperatures <0°C
In unfavourable conditions, it is possible that the power tool may
switch itself off due to electrostatic discharge. After switching the
power tool back on again, it will work as intended.
Noise/vibration information
Noise emission values determined according to
EN62841-2-14.
Typically, the A-weighted sound pressure level of the power
tool is 79 dB(A). Uncertainty K = 3 dB. The noise level when
working can exceed 80 dB(A).
Wear hearing protection
Total vibration values ah (triax vector sum) and uncertainty K
determined according to EN62841-2-14:
ah <2.5 m/s2, K = 1.5 m/s2,
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Fitting
uRemove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Battery Charging
uUse only the chargers listed on the accessories page.
Only these chargers are matched to the lithium-ion bat-
tery of your power tool.
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
uDo not continue to press the On/Off switch after the
power tool has automatically switched off. The battery
can be damaged.
Follow the instructions on correct disposal.
Removing the battery
To remove the battery (5), press the release button (6) and
pull the battery to the rear and out of the power tool. Do not
use force to do this.
Changing the Tool
The hex key (18) required for changing the planer blade is
housed inside the power tool and should always be stored
there (see figure F).
uTake care when changing the planer blade. Do not pick
up the planer blade by the cutting edges. You may be
injured by the sharp cutting edges.
Use only original Bosch HM/TC planer blades.
The hard metal (HM/TC) planer blade has two cutting edges
and can be turned. If both cutting edges become blunt, the
planer blade (17) needs to be changed. The HM/TC planer
blade must not be resharpened.
Removing the planer blade (see figure A)
To turn or replace the planer blade (17), turn the blade head
(19) until it is parallel to the adjustable planer base plate
(14).
Bosch Power Tools 1 609 92A 4LD | (19.02.2019)
… 15 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Bosch GHO 12V-20 Professional wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info