Bedienungsanleitung Bosch GNH 18V-64 (Seite 21 von 315) (Alle Sprachen)

786282

Zoom out

Zoom in

Vorherige Seite

1/315

Nächste Seite

English | 21

– Push the nail strip forwards in the magazine until the last

nail is positioned in front of the magazine spring(17).

Note: A lock function of the magazine slider prevents the

power tool from being started with an empty magazine. The

discharge lock-off cannot be pressed down and blank firing

is thus prevented.

– Press the pretensioned nail pusher(14) against the

magazine slider(13) and, at the same time, pull the

magazine slider completely to the end of the

magazine(12).

Note: The magazine slider must slide back with only low

force (finger-pressure). A tight-running magazine slider

causes the nails to be driven in at an incorrect angle.

– With the nail pusher(13) pressed, carefully guide the

magazine slider(14) forwards until the nail pusher is over

the last nail, thus pushing the nail strip in the magazine

completely to the front.

Note: Do not let the magazine slider snap back without guid-

ing it. This could damage the magazine slider and there is a

risk of getting your fingers caught.

Operation

Actuation systems

Single actuation with safety run

With this actuation system, the discharge lock-off(2) must

first be firmly pressed against the workpiece. A fastener is

not discharged until the trigger(5) is pulled.

Afterwards, further discharging procedures can only be ac-

tuated when the trigger and the discharge lock-off have been

set back to the starting position.

Contact actuation with automatic return

(GNH18V-64M)

With this actuation system, the trigger(5) must be pulled

first and held in this position. Afterwards, the discharge

lock-off must be firmly pressed against the workpiece in or-

der to discharge the fastener. (5)Further discharging pro-

cedures can be actuated by repositioning it elsewhere, while

the trigger is pushed.

In contact actuation mode, a nail can also be driven in with

single actuation.

Starting Operation

uRemove the battery from the power tool before carry-

ing out work on the power tool (e.g. maintenance,

changing tool, etc.). The battery should also be re-

moved for transport and storage. There is risk of injury

from unintentionally pressing the on/off switch.

Inserting the Battery

– Push the charged battery(7) into the battery bay of the

power tool until the battery is securely locked.

Switching On and Off (see figureB1B2)

– To switch on the power tool, press the on/off switch

button(18) for at least 1 second.

The on/off switch display(19) lights up green.

GNH18V-64M: If single actuation is activated, the

display(20) lights up white.

– To switch off the power tool, press the on/off switch

button(18) for at least 1 second.

Discharging the nails – single actuation (see

figureB1B2)

– Switch on the power tool.

– Firmly position the outlet(15) or the rubber workpiece

protector(1) on the workpiece until the discharge lock-

off(2) is pressed down completely.

– Afterwards, briefly press the trigger(5) and release it

again.

This discharges a nail.

– Allow the power tool to bounce back from the workpiece.

– For another driving procedure, completely lift the power

tool from the workpiece and position it firmly at the next

required location.

Discharging the nails – contact actuation (seefigureB1)

(GNH18V-64M)

– Switch on the power tool.

– Activate the contact actuation by briefly pressing the on/

off switch button(18).

The contact actuation display(21) lights up white.

– Press and hold the trigger(5).

– Firmly position the outlet(15) or the rubber workpiece

protector(1) on the workpiece until the discharge lock-

off(2) is pressed down completely.

This discharges a nail.

– For another discharging procedure, keep the trigger(5)

pressed and completely lift the power tool from the work-

piece. Replace it firmly in the next required position.

Working Advice

uRemove the battery from the power tool before carry-

ing out work on the power tool (e.g. maintenance,

changing tool, etc.). The battery should also be re-

moved for transport and storage. There is risk of injury

from unintentionally pressing the on/off switch.

Before starting work, always check that the safety and actu-

ation devices are functioning correctly and that all screws

and nuts are tightly seated.

If a power tool is defective or not functioning properly, dis-

connect it immediately from the power supply and contact

an authorised Bosch after-sales service centre. .

Do not perform any incorrect manipulations on the power

tool. Do not disassemble or block any components of the

power tool, such as the discharge lock-off.

Do not carry out "emergency repairs" with unsuitable means.

The power tool is to be maintained regularly and properly.

Avoid any tampering and damage to the power tool, e.g.

from:

– Imprinting or engraving,

– Retrofitting measures not approved by the manufacturer,

Bosch Power Tools 1 609 92A 81N | (01.08.2022)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GNH 18V-64 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info