Bedienungsanleitung Bosch GNH 18V-64 (Seite 22 von 315) (Alle Sprachen)

786282

Zoom out

Zoom in

Vorherige Seite

1/315

Nächste Seite

22 | English

– Guiding along templates manufactured of hard material,

e.g. steel,

– Dropping on or sliding over the floor,

– Using as a hammer,

– Applying any kind of force.

Make sure to check whatever is below or behind your work-

piece. Do not shoot nails into walls, ceilings or floors, when

persons are behind them. The nails can burst through the

workpiece and injure someone.

Do not shoot a nail onto an already driven-in one. This could

cause the nail to deform, the nails could become jammed or

the power tool could move in an uncontrolled manner.

When the power tool is used under cold ambient conditions,

the first nails will be driven in slower than usual. Once the

power tool has warmed up during working, normal operating

speed will be regained.

Avoid pulling the trigger when the magazine is empty to min-

imise wear on the firing pin.

For longer work breaks or after finishing work, switch off the

power tool, remove the battery and empty the magazine if

possible.

Emptying the magazine (seefiguresC1–C2)

– With the nail pusher(13) pressed, pull the magazine

slider(14) backwards until the last nail is free; then care-

fully guide the magazine slider forwards to the beginning

of the magazine(12).

Note: Do not let the magazine slider snap back without guid-

ing it. This could damage the magazine slider and there is a

risk of getting your fingers caught.

– Turn the power tool so that the nails in the magazine slide

back to the magazine spring(17).

– Press the magazine spring down and allow the nails to

slide past the nail pusher(14) out of the magazine(12).

Adjusting the depth stop (seefigureD)

The driving depth of the nails can be set with the

thumbwheel(4).

– Empty the magazine(12).

–Nails are driven in too deep: To reduce

the driving depth, turn the

thumbwheel(4) anticlockwise.

–Nails are not driven in deep enough: To

increase the driving depth, turn the

thumbwheel(4) clockwise.

– Refill the magazine.

– Test the new driving depth on a test workpiece.

Repeat the worksteps as required.

Clearing jams (seefiguresE1–E2)

Single nails can become jammed in the shot duct. If this

should occur frequently, please contact an authorised Bosch

after-sales service centre.

Note: If the driver blade does not return after clearing a jam,

please contact an authorised Bosch after-sales service

centre.

– Release the trigger(5).

– Switch the power tool off and remove the battery(7).

– Empty the magazine(12).

– Press the clamping lever(3) down so that the shot duct

opens.

– Remove the jammed nail. Use a pair of pliers for this, if re-

quired.

– Close the shot duct, hang the clip of the clamping

lever(3) into the hooks on the shot duct and then push

the clamping lever up again.

– Refill the magazine.

Changing the workpiece protector (seefigureF)

The workpiece protector(1) at the end of the discharge

lock-off(2) protects the workpiece until the power tool is

correctly placed for the discharging procedure. The work-

piece protector can be removed and replaced

– Release the trigger(5).

– Switch the power tool off and remove the battery(7).

– Empty the magazine(12).

– Remove the workpiece protector from the discharge lock-

off.

– Push the new workpiece protector with the open end over

the discharge lock-off.

Note: A spare workpiece protector can be stored on top of

the magazine(12). For this, push the workpiece protector

into the storage compartment(10).

Transport and Storage

For transport, switch off the power tool; especially when us-

ing ladders or moving in an unusual stance or posture.

At the workplace, carry the power tool only by the handle(8)

and with the trigger(5) released.

Always store the power tool disconnected from the battery

and in a dry and warm location.

When not using the power tool for an extended period of

time, apply a fine oil coating to steel parts. This prevents the

formation of rust.

Maintenance and Service

Maintenance and Cleaning

uRemove the battery from the power tool before carry-

ing out work on the power tool (e.g. maintenance,

changing tool, etc.). The battery should also be re-

moved for transport and storage. There is risk of injury

from unintentionally pressing the on/off switch.

uTo ensure safe and efficient operation, always keep

the power tool and the ventilation slots clean.

1 609 92A 81N | (01.08.2022) Bosch Power Tools

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GNH 18V-64 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info