Bedienungsanleitung Bosch GWS 24-230 JBX (Seite 19 von 135) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

79055

Zoom out

Zoom in

Vorherige Seite

1/135

Nächste Seite

English - 5

Safety warnings specific for wire brushing

operations

■ Be aware that wire bristles are thrown by

the brush even during ordinary operation.

Do not overstress the wires by applying ex-

cessive load to the brush. The wire bristles

can easily penetrate light clothing and/or skin.

■ If the use of a guard is recommended for

wire brushing, do not allow any interfer-

ence of the wire wheel or brush with the

guard. Wire wheel or brush may expand in di-

ameter due to work load and centrifugal

forces.

Additional safety instructions

■ Use suitable detectors to determine if util-

ity lines are hidden in the work area or call

the local utility company for assistance.

Contact with electric lines can lead to fire and

electric shock. Damaging a gas line can lead

to explosion. Penetrating a water line causes

property damage or may cause an electric

shock.

■ If the power supply should be discon-

nected, e. g. due to a power outage or pull-

ing the mains plug, release the On/Off

switch and set it to the Off position. This

prevents uncontrolled restarting.

■ When working stone, use dust extraction.

The vacuum cleaner must be approved for

the extraction of stone dust. Using this

equipment reduces dust-related hazards.

■ Use a cutting guide when cutting stone.

Without sideward guidance, the cutting disc

can jam and cause kickback.

■ Before any work on the machine itself, pull the

mains plug.

■ For work with grinding or cutting discs, the pro-

tection guard 7 must be mounted.

Protection Guard with Locking Screw

The coded projection 13 on the protection

guard 7 ensures that only a guard that fits the

machine type can be mounted.

Loosen the clamping screw 12, if necessary.

Place the protection guard 7 with coded projec-

tion 13 into the coded groove on the spindle col-

lar of the machine head and rotate to the required

position (working position).

The closed side of the protection guard 7

must always point to the operator.

Tighten clamping screw 12.

Always pay attention that the protection

guard 7 is firmly seated on the spindle collar.

Protection Guard with Quick Clamp

Open the clamping lever 9.

Place the protection guard 7 with coded projec-

tion 13 into the coded groove on the spindle col-

lar of the machine head and rotate to the required

position (working position).

The closed side of the protection guard 7

must always point to the operator.

To fasten the protection guard 7, close the

clamping lever 9.

Always pay attention that the protection

guard 7 is firmly seated on the spindle collar.

The tightening tension of the clamping bracket

can be changed by releasing or tightening the ad-

justing screw 8.

Mounting the

Protective Devices

1 609 929 H82.book Seite 5 Dienstag, 3. Mai 2005 3:11 15

20 • 1 609 929 H82 • TMS • 28.04.05

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GWS 24-230 JBX Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info