Bedienungsanleitung Bosch GWS 24-230 JBX (Seite 21 von 135) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

79055

Zoom out

Zoom in

Vorherige Seite

1/135

Nächste Seite

English - 7

Flap Disc

For operations with the rubber sanding

plate/the cup brush/the wheel brush /the flap

disc, always mount the hand guard (acces-

sory).

Position the flap disc on the grinder spindle 6.

Screw on the quick-clamping nut 11 and tighten

the flap disc.

Rubber Sanding Plate 19

For operations with the rubber sanding

plate/the cup brush/the wheel brush /the flap

disc, always mount the hand guard (acces-

sory).

For mounting, see the illustration page.

Screw on the round nut 21 and tighten with the

two-pin spanner.

Increased effort must be taken into account when

loosening the round nut 21.

Cup Brush 22/Disc Brush

For operations with the rubber sanding

plate/the cup brush/the wheel brush /the flap

disc, always mount the hand guard (acces-

sory).

The grinding tool must be able to be screwed

onto the grinding spindle 6 until it rests firmly

against the grinder spindle flange at the end of

the grinder spindle threads. Tighten with an

open-end spanner.

Increased effort must be taken into account when

loosening the grinding tool.

Grinding Cup

When working with grinding cups, use

the special guard 14.

The grinding cup 15 should always protrude

from the guard 14 only as far as absolutely nec-

essary for the work to be performed in each case.

Adjust the guard 14 to this distance.

For mounting, see the illustration page.

Screw the clamping nut 16 on to the grinder spin-

dle 6 ensuring that the flat side faces the grinding

disc and tighten the clamping nut with the fitting

offset two-pin spanner 17.

Increased effort must be taken into account when

loosening the clamping nut 16.

All grinding tools mentioned in these operating in-

structions can be used.

The permissible speed [rpm] or the circumferen-

tial speed [m/s] of the grinding tools used must at

least match the values given in the table.

Therefore, always observe the permissible

rotational/circumferential speed on the label

of the grinding tool.

Observe correct mains voltage: The voltage of

the power source must agree with the voltage

specified on the nameplate of the machine.

Equipment marked with 230 V can also be con-

nected to 220 V.

Switching On and Off

To start the machine, press the On/Off switch 3

forward and then down.

To lock-on, push the pressed On/Off switch 3

further forwards.

To switch off the machine, release the On/Off

switch 3 or push and release it then.

Switch version without lock

(country-specific):

To start the machine, press the On/Off switch 3

forward and then down.

To switch off the machine, release the On/Off

switch 3.

Approved Grinding Tools

max.

[mm] [mm]

Db d[rpm] [m/s]

180

230

22.2

8 500

6 500

180

230

–

8 500

6 500

100 30 M 14 8 500 45

Starting Operation

1 609 929 H82.book Seite 7 Dienstag, 3. Mai 2005 3:11 15

22 • 1 609 929 H82 • TMS • 28.04.05

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch GWS 24-230 JBX Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info