Bedienungsanleitung Bosch PFS 3000-2 (Seite 21 von 274) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

544011

Zoom out

Zoom in

Vorherige Seite

1/274

Nächste Seite

English | 21

Bosch Power Tools 2 609 007 771 | (28.2.14)

Robert Bosch GmbH, Power Tools Division

D-70745 Leinfelden-Echterdingen

Leinfelden, 28.02.2014

Assembly

 Before any work on the machine itself, pull the mains

plug.

 Ensure that the spray gun and base unit are assembled

completely and with all seals. Only this will ensure the

function and safety of the fine-spray system.

Connecting the Air Hose (see figuresA1 – A3)

– Open the elastic band 23 and completely unwind the air

hose 18.

Connecting the base unit:

– Insert a bayonet lock 19 of the air hose securely into the

slots in the base unit port 27 according to the arrow marks.

– Turn the bayonet lock a quarter turn clockwise.

Connecting to the spray gun:

– Insert the second bayonet lock 19 of the air hose securely

into the slots in the spray gun port 8 according to the arrow

marks.

– Turn the bayonet lock a quarter turn clockwise.

Note: Remove the air hose 18 before pouring in spray materi-

al (quarter turn of the bayonet lock 19 counterclockwise; pull

the bayonet lock 19 out of the port 8).

Changing the Nozzle Cap (see figures B1–B2)

The fine-spray system is supplied with two nozzle caps:

Note: Check the spray material by stirring it before selecting

the nozzle cap. Thin-viscosity material (e.g. wood paint) can

be sprayed better with the grey nozzle cap 10. Thick-viscosity

material (e.g. wood lacquer or wall paint) can be sprayed bet-

ter with the white nozzle cap 9.

– To change the nozzle cap, unscrew the union nut 3.

– Pull off the air cap 2.

– Unscrew the mounted nozzle cap.

– Open the air filter cover 26 and take the required nozzle

cap out of the accessory compartment 28.

– Screw the required nozzle cap onto the thread in the spray

gun.

–Put the air cap 2 on the nozzle cap and tighten it with the

union nut 3.

Operation

 Before any work on the machine itself, pull the mains

plug.

Preparing for Operation

 Spraying on the sides of water bodies (lakes, rivers,

etc.) or neighbouring surfaces in the direct catchment

area is not permitted.

When purchasing paint, varnish and spray material, pay at-

tention to their environmental compatibility.

Preparing the Spray Surface

The spray surface must be clean, dry and grease-free.

– Roughen smooth surfaces and then remove the sanding

dust.

When spraying, all non-covered surfaces can be soiled by the

spray mist. Therefore, thoroughly prepare the area around

the surface to be sprayed:

– Cover or mask off floors, furnishings, doors, windows as

well as door and window frames, etc.

Preparing the Spray Material

– Stir the spray material thoroughly.

– Dilute the spray material if necessary.

 When diluting, pay attention that the spray material

and the diluting agent correspond. When using a faulty

diluting agent, lumps can develop that can lead to clogging

of the spray gun.

 When diluting the spray material, make sure that the

flash point of the mixture is above 55 °C again after di-

luting. Diluting e.g. solvent-based lacquers lowers the

flash point.

Filling in Spray Material (see figures C1–C2)

Note: Remove the air hose 18 before pouring in spray materi-

al (quarter turn of the bayonet lock 19 counterclockwise; pull

the bayonet lock 19 out of the port 8).

– When using large buckets, pour the spray material into a

smaller transfer bucket 12 if necessary (e.g. 10-l wall paint

into an empty 2.5 or 5.0-l bucket).

– Pull the spray gun off the container 7.

– If you are using already opened spray material, place the

thoroughly cleaned filling sieve 11 on the container 7 to

hold back any lumps of paint when pouring in.

Henk Becker

Executive Vice President

Engineering

Helmut Heinzelmann

Head of Product Certification

PT/ETM9

Nozzle cap 9 Nozzle cap 10

Colour white grey

Delivery

condition

Mounted In the accessory compart-

ment 28 under the air fil-

ter cover 26

Application “Wall” “Wood”

Spray material Recommended

dilution

Wood stains, oils, glazes, impregna-

tions, anti-rust primers

Solvent-dilutable or water-dilutable

lacquers, primers, radiator lacquers,

thick-coat glazes

0 –10%

Emulsion paint, latex paint 0–10%

– Hold the spray gun in place with one hand and use

the other hand to turn the container 7 towards the

open symbol.

OBJ_BUCH-2024-002.book Page 21 Friday, February 28, 2014 9:28 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PFS 3000-2 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info