Bedienungsanleitung Bosch PFS 3000-2 (Seite 22 von 274) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

544011

Zoom out

Zoom in

Vorherige Seite

1/274

Nächste Seite

22 | English

2 609 007 771 | (28.2.14) Bosch Power Tools

– Pour the spray material into the container 7 up to no more

than the 1000 mark.

– Carry out a test-spray run on a test surface. (see “Spray-

ing”, page 22)

When the spraying pattern is perfect, start the spray job.

When the spraying result is not satisfactory or when no paint

comes out, please continue as described under “Correction of

Malfunctions” on page 24.

Starting Operation

 Observe the mains voltage! The voltage of the power

source must correspond with the data on the type plate of

the machine.

 Pay attention that the base unit cannot draw in dust or

other contamination during operation.

 Make sure never to spray on the base unit.

 Stop spraying if fluid escapes from places other than

the intended nozzle during spraying, and restore the

spray gun to its proper condition. There is a risk of elec-

tric shock.

 Do not direct the fine-spray system against yourself,

other persons or animals.

Switching On (see figure D)

To save energy, only switch the fine-spray system on when

you are using it.

– Check whether the correct nozzle cap is mounted (see

“Changing the Nozzle Cap”, page 21).

– Plug the mains plug into a socket outlet.

– Grasp the spray gun by the handle and point it at the spray

surface.

– Set the sliding switch 24 to the required application to reg-

ulate the air flow (see also “Adjusting the Air Flow”,

page 23).

– Pull the trigger switch 5 on the spray gun.

Note: When the base unit is switched on, air always flows out

at the nozzle .

Switching Off

– Let go of the trigger switch 5 and slide the sliding switch 24

all the way to the left (position ).

– Pull the mains plug from the socket outlet.

Working Advice

Spraying (see figures E –H)

Note: Observe the wind direction when operating the power

tool outdoors.

– Firstly, carry out a test-spray run and adjust the spray pat-

tern and the spray material quantity according to the spray

material. (For adjustments, see the following sections)

– Be absolutely sure to hold the spray gun at a consistent dis-

tance of 20 –25 cm perpendicular to the spray object.

– Begin the spraying procedure outside the target area.

– Move the spray gun evenly cross-wise or up-and-down, de-

pending on the spray pattern setting.

An even surface quality is achieved when the paths overlap

by 4 – 5cm.

– When spraying horizontal objects or spraying overhead,

hold the spray gun at a slight angle and back away from the

sprayed surface.

Risk of stumbling! Pay attention to possible obstacles

in the room.

– Avoid interruptions within the spray surface.

Guiding the spray gun evenly will provide uniform surface

quality.

Non-uniform clearance and spray angle lead to heavy forma-

tion of paint mist and thus to an uneven surface.

– End the spraying procedure outside the target area.

Never completely empty the container for the spray material

by spraying. If the suction tube is no longer immersed in the

spray material, the spray jet will be interrupted and this will

result in an inconsistent surface.

If spray material settles on the air cap 2 or the nozzle cap,

clean the components with the supplied cleaning brush 25.

Adjusting the Spray Pattern (see figure I)

 Never actuate the trigger switch 5 while adjusting the

air cap 2.

–Turn the air cap 2 to the requested position.

Adjusting the Spraying Capacity (see figure J)

(PAINTVolume)

– Turn the thumbwheel 4 to set the required spraying capac-

ity:

Settings 1/2/3: “wood” application,

settings 3/4/5: “wall” application.

– Put the spray gun on the container 7. Turn the con-

tainer 7 towards the close symbol until you hear the

lock ring 6 engage.

Air cap Spray jet pattern Application

Vertical flat jet for

horizontal working

direction

Horizontal flat jet

for vertical working

direction

Round jet for cor-

ners, edges and

hard to reach loca-

tions

OBJ_BUCH-2024-002.book Page 22 Friday, February 28, 2014 9:28 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bosch PFS 3000-2 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info